EasyManua.ls Logo

Land Pride RC3615 - User Manual

Land Pride RC3615
54 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Table of Contents
Cover photo may show optional equipment
not supplied with standard unit.
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
!
© Copyright 2015 Printed
27852
R
C3615 (540 RPM) and RCM3615 (1000 RPM) S/N 945022-
Rotary Cutters
330-502M
Operator’s Manual
4/20/15

Questions and Answers

  • D
    David DillonAug 21, 2025
    Why are the blades wearing excessively on my Land Pride RC3615 Farm Equipment?
    • K
      kimberlyrobinsonAug 21, 2025
      If the blades on your Land Pride farm equipment are wearing excessively, it may be due to cutting on sandy ground or frequently contacting the ground. To resolve this, raise the cutting height.
  • M
    meganmarksAug 23, 2025
    Why are the blades coming loose on my Land Pride farm equipment?
    • W
      william07Aug 23, 2025
      If the blades are coming loose on your Land Pride farm equipment, ensure that the blade hardware is properly tightened, referring to “Cutter Blade Maintenance” on page 32. Also, operate the cutter at the correct PTO speed to avoid over-speeding.
  • J
    Jose Hughes Jr.Aug 26, 2025
    What causes the blades to lock up on my Land Pride farm equipment?
    • Y
      yaustinAug 26, 2025
      Blades on your Land Pride farm equipment might lock up for a few reasons. If the blades were locked together (overlapped) when the wings were raised to the transport position, use a pry bar or other tool to separate them before lowering the wings. If your tractor has an instant-on PTO, engage the PTO at low RPMs and then slowly increase the engine speed to full PTO speed, referring to “Engage Blades” on page 26. If your tractor has an instant-off PTO, decrease the engine speed slowly to an idle and then disengage the PTO, referring to “Disengage Blades” on page 27.
  • J
    James BridgesAug 28, 2025
    Why is the oil seal leaking on my Land Pride RC3615?
    • J
      Jeffrey HardinAug 28, 2025
      If the oil seal is leaking on your Land Pride farm equipment, it could be due to several reasons. First, check if the gearbox is overfilled and drain the oil to the correct level using the fill hole or the dipstick's full mark. Another cause might be damaged seals, which would require replacement. Also, ensure that grass or wire isn't wrapped around the shaft in the seal area; clean it off and inspect the seal areas regularly.
  • M
    morrisonwayneAug 29, 2025
    What to do if my Land Pride RC3615 has excessive vibration?
    • Z
      Zachary BakerAug 30, 2025
      Excessive vibration in your Land Pride farm equipment can stem from several issues. Start by inspecting the area before cutting to avoid hitting solid objects. Other potential causes include a bent driveline (replace the driveline or distribution shaft), a bent blade carrier (replace the blade carrier), or a broken blade (replace the blade). Also, ensure that all blades can swing freely. If you experience high torque start-up or hit solid objects, disassemble and inspect the driveline for incorrectly located needles or damaged bearing caps. Finally, ensure blades have equal weight, replacing each pair of blades on the affected carrier if necessary.
  • M
    Melissa AndersonSep 1, 2025
    Why is the driveline yoke or cross failing on my Land Pride RC3615?
    • K
      Kyle RodriguezSep 1, 2025
      A failing driveline yoke or cross on your Land Pride farm equipment can be attributed to a few factors. One common cause is a frozen clutch; address this by slipping the clutches according to the instructions under “Drivelines With Slip Clutches” on page 34. Another reason could be shock loading from hitting solid objects, so avoid doing that. Lastly, ensure that you lubricate the driveline every 8 hours.
  • K
    karenmillsSep 3, 2025
    How to fix a bent driveline shaft on Land Pride RC3615?
    • E
      Elizabeth Cook MDSep 3, 2025
      A bent driveline shaft on your Land Pride farm equipment can occur if it's contacting the frame or drawbar, or bottoming out. To fix this, reduce the lift height in transport position, reposition the drawbar, or shorten the driveline shaft, respectively. Also, ensure that the shaft is lubricated enough.
  • S
    shane69Sep 5, 2025
    What to do if Slip Clutches slip even with a light load on my Land Pride RC3615?
    • T
      Tracy WatsonSep 5, 2025
      If the slip clutches on your Land Pride farm equipment are slipping even with a light load, it could be due to several reasons. You might be scalping the ground, in which case you should raise the cutting height. Another cause could be that the clutch is not properly adjusted, so adjust it per instructions under “Drivelines With Slip Clutches” on page 34. It's also possible that the clutch plates are worn out and need replacement, or that there is a foreign object caught between the clutch plates, which needs to be removed.
  • K
    Kevin KimSep 7, 2025
    What causes excessive side skid wear on Land Pride farm equipment?
    • C
      Christian BrownSep 7, 2025
      Excessive side skid wear on your Land Pride farm equipment can be caused by abrasive soil or cutting too low. Adjust the cutter height or raise the cutting height to mitigate this issue.
  • B
    Brian GomezSep 9, 2025
    Why is the blade carrier bent on my Land Pride farm equipment?
    • B
      barrontylerSep 9, 2025
      The blade carrier on your Land Pride farm equipment may be bent because you are hitting solid objects. Avoid hitting solid objects.

Summary

Important Safety Information

General Safety Rules

Covers essential safety rules, hazard symbols, and signal words for safe operation.

Tractor Shutdown and Storage

Procedures for safely shutting down the tractor and storing the implement.

Operational Safety Guidelines

Guidelines for safe operation, transport, maintenance, and visibility.

Personal Safety and Hazard Control

Discusses protective gear, fluid hazards, tire safety, ROPS, and rider policies.

Safety Labels and Identification

Details on identifying, maintaining, and replacing safety labels.

Section 1: Assembly & Set-up

Tractor and Hitch Requirements

Details tractor compatibility, drawbar setup, and available hitch types.

Hitch & Jack Assembly

Instructions for assembling the hitch, turnbuckle, and parking jack.

Hitch Hook-up Procedures

Step-by-step guides for connecting standard and optional hitches.

Driveline, Hydraulics, and Disassembly

Guides for driveline installation, hydraulic connections, and system purging.

Section 2: Adjustments

Center and Wing Deck Leveling

Procedures for adjusting the cutter decks for proper ground contact.

Cutting Height Adjustment

Instructions on setting the desired cutting height using stroke control spacers.

Section 3: Operating Instructions

Startup Checklist and Safety

Essential pre-operation checks and safety information.

Transporting the Cutter

Guidelines for safely moving the cutter and engaging transport locks.

Blade Operation and Control

Procedures for blade inspection, engagement, and disengagement.

Field Setup and General Operation

Steps for field setup, gear selection, and mowing best practices.

Section 4: Options & Accessories

Safety Guards and Tire Options

Details on available safety guards and tire types.

Hitch Options

Lists available hitch types beyond the standard clevis hitch.

Hydraulic and Mechanical Wing Lifts

Information on kits for independent wing control and mechanical lifts.

Section 5: Maintenance & Lubrication

General Maintenance and Tractor Care

Routine checks, part replacement, and tractor hydraulic system care.

Cutter Blade and Driveline Maintenance

Procedures for blades, clutches, and driveline systems.

Skid Shoe, Tire, and Storage Procedures

Guidance on skid shoes, tire maintenance, and long-term storage.

Lubrication Points and Intervals

Details all lubrication points, types of grease, and service intervals.

Section 6: Specifications & Capacities

Machine Specifications and Dimensions

Lists key technical specifications like horsepower, weight, and dimensions.

Driveline and Blade Details

Information on driveline types, blade speed, overlap, and bolts.

Section 7: Features & Benefits

Cutter Features and Advantages

Highlights key features and their benefits for operation and durability.

Section 8: Troubleshooting

Common Problems and Solutions

A chart detailing common issues, their causes, and recommended solutions.

Section 9: Torque & Tire Inflation Chart

Torque Values for Fasteners

Charts providing torque specifications for various bolt sizes and grades.

Tire Inflation Guidelines

Recommended tire inflation pressures for specific tire sizes.

Section 10: Warranty

Land Pride Product Warranty

Outlines the warranty coverage, limitations, and claim procedures.

Land Pride RC3615 Specifications

General IconGeneral
BrandLand Pride
ModelRC3615
CategoryFarm Equipment
LanguageEnglish

Related product manuals