Laney
1.
22
19
HEAD PHONE SOCKET: Socket for connecting external headphones. Connecting
headphones automatically isolates the internal speaker.
LINE OUT: Socket provided for connecting to an external power amplifier, Front of house
PA or an external recording device. The signal from this socket is a standard line level
signal.
INSERT LOOP RETURN: Socket for connecting the sends of external devices such as
effects processors. Should be used in conjunction with 23.
INSERT LOOP SEND: Socket for connecting to the input of external devices such as
effects processors. Should be used in conjunction with 22.
RETURNRETURN
INSERTINSERT
LINELINE
OUTOUTPHONESPHONES
HEADHEAD
SPEAKER OUTPUTSPEAKER OUTPUT
A TOTAL LOAD OF NO LESS THANA TOTAL LOAD OF NO LESS THAN
4 OHMS CAN BE CONNECTED AT4 OHMS CAN BE CONNECTED AT
ANY ONE TIMEANY ONE TIME
REFER TO USER MANUAL FORREFER TO USER MANUAL FOR
RECOMMENDED CONNECTIONS.RECOMMENDED CONNECTIONS.
!!
CAUTIONCAUTION
RISK OF ELECTRIC SHOCK - DO NOT OPENRISK OF ELECTRIC SHOCK - DO NOT OPEN
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCKWARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF
FIRE REPLACE ONLY WITH SAME TYPE AND RATED FUSE.
CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF
FIRE REPLACE ONLY WITH SAME TYPE AND RATED FUSE.
ATTENTION REMPLACER LE FUSIBLE PAR LE MEME ET LE CALIBRE.ATTENTION REMPLACER LE FUSIBLE PAR LE MEME ET LE CALIBRE.
SUPPLY VOLTAGE
& FUSE RATING
SUPPLY VOLTAGE
& FUSE RATING
~115V T5A
~230V T2A
~115V T5A
~230V T2A
200 WATTS ~50/60 Hz200 WATTS ~50/60 Hz
MAXIMUM POWER CONSUMPTIONMAXIMUM POWER CONSUMPTION
Made in the United Kingdom by BLT Industries Ltd.Made in the United Kingdom by BLT Industries Ltd.
WARNING THIS EQUIPMENT MUST BE EARTHED.WARNING THIS EQUIPMENT MUST BE EARTHED.
ATTENTION DEBRACHER A LA PRISE SECTEUR AVANT D’OUVRIR.ATTENTION DEBRACHER A LA PRISE SECTEUR AVANT D’OUVRIR.
SERIAL No:-SERIAL No:-
SENDSEND
008822008822
20
23
21
20
21
23
22
1
2
PassivePassive
TrebleTrebleMidMid
BassBass
compressorcompressor
22
++
00
--
66
55
44
5500 1010
22
33
44
11
22
33
55
44
33
66
55
44
88
99
77
101000
22
11
33
00
11
HCM30BHCM30B
axax
oreore
ardard
PowerPower
speakerspeaker
ExternalExternal
phonesphones
HeadHead
outout
DirectDirect
InIn
CD / LineCD / Line
VolumeVolume
EqualizationEqualization
SweepSweep
GainGain
ActiveActive
99
77
88
55
44
66
00 1010
22
11
33
88
99
77
InputInput
HH
CC
MM
22
++
00
--
55
33
44
22
55
44
33
22
++
00
--
55
33
44
22
55
44
33
GainGain
HCM30B
3
1
4
9
10
11
2
5
6
7
8
12 13
10
PASSIVE INPUT: Socket provided for connecting a bass guitar equipped with passive
pickups.
ACTIVE INPUT: Socket provided for connecting a bass guitar equipped with active pickups.
COMPRESSOR GAIN: Sets the level of compression of the input signal. Should be used to
give a punchy bass sound as desired.
COMPRESSOR SWITCH: Activates the on board compressor.
BASS: Sets the level of bass frequencies present in the signal..
SWEPT MID SWEEP: Sets the frequency at which the swept mid gain control is applied.
SWEPT MID GAIN: Sets the amount of gain applied to the frequency selected by control 6.
TREBLE: Sets the level of high frequencies present in the signal
VOLUME: Sets the overall listening volume of the amplifier.
CD/LINE INPUT: Sockets for connection of external CD player.
DI: Socket provided for connecting the amplifier to an external amplifier such as front of
house PA or providing a direct input into a recording device.
EXTERNAL SPEAKER: Socket for connecting an external 4/8 Ohm speaker enclosure.
Connecting an external speaker automatically isolates the internal speaker.
HEAD PHONES: Socket for connecting external headphones. Connecting headphones
automatically isolates the internal speaker.
3
11
13
9
12
5
6
8
4
7
5
To Next Page
Loading...
Need help?
General