Lansinoh Smartpump - Breast Pump Parts and Cleaning; Lansinoh Smartpump Parts List; Cleaning Instructions

8 9
Lansinoh
®
Smartpump
™
Breast Pump Parts
Item Item Number
A. Smartpump
™
Tubing #53403
A1 Silicone Tubes 300 mm (2)
A2 Silicone Tube 600 mm
A3 Smartpump
™
Tubing Y Connector #53405
A4 Smartpump
™
Pump Connnector #53453
B. Breastmilk Expression Set Includes:
B1 ComfortFit
™
Breast Flange 25mm (2) #50408
B2 ComfortFit
™
Breast Flange 30.5mm (2) #53408
B3 Smartpump
™
Breast Flange Body (2) #53454
B4 Smartpump
™
Diaphragm (2) #53402
B5 Smartpump
™
Diaphragm Cap (2) #53410
B6 White Valve (2 + 2 extra) #53401
B7 5 oz (150 ml) Bottle (4 ), (2 ) #53451
B8 NaturalWave
®
Slow Flow Nipples (2) #71027
C. Storage Lids (4 ), (2 ) #53450
D. Smartpump
™
AC Adapter/power cord #50409
E. Wide Neck Bottle Holder (2) #53452
Two extra white valves are included. To order replacement parts please visit
www.Lansinoh.com/store.
3.1 Before First Use
1. Always wash and dry hands thoroughly with soap and
water before handling the breastmilk expression set.
2. Disassemble the breastmilk expression set and place
parts in a large pot.
3. Cover the parts in water making sure there is room for
all of the parts to oat freely in the pot.
4. Bring the water to a boil and allow the parts to boil for 5 minutes.
5. After boiling remove the parts from the pot with tongs and place on a clean
towel to dry, covering the parts with a second towel.
6. Allow the parts to dry completely before assembly and use. Partially dried parts
may aect the operation of the pump.
7. Once parts are dry they can be stored in a clean plastic bin with a lid or in a
clean plastic zipper bag.
3.3 Before Each Use
1. Always wash and dry hands thoroughly with soap and water before handling the
breastmilk expression set.
2. Before assembling the breastmilk expression set, be sure that all of the parts are
completely dry.
3. Visually inspect the individual components for cracks, chips, tears, discoloration
or deterioration. These may aect the functionality of the pump.
4. Should you have any questions or concerns about your parts please contact
Lansinoh at 800-292-4794 for further guidance.
5. To purchase replacement parts for your pump please visit Lansinoh.com/Store
3.2 Cleaning and Sanitization after Each Use
1. Disassemble the breastmilk expression set, setting aside the tubing and
connectors.
2. Rinse all parts with cold water immediately after each use.
3. Hand wash all parts of the breastmilk expression set using warm soapy water.
A nipple brush may be used to scrub the hard plastic pieces of the breastmilk
expression set, but should not be used on the soft silicone valve or diaphragm.
4. Rinse parts with clean, warm water.
5. Place parts in a pot and cover with water making sure there is room for all of the
parts to oat freely in the pot.
6. Bring the water to a boil and allow the parts to boil for 5 minutes.
7. After boiling remove the parts from the pot with tongs and place on a clean
towel to dry, covering the parts with a second clean towel.
8. Allow the parts to dry completely before assembly and use. Partially dried parts
may aect the operation of the pump.
9. Once parts are dry they can be stored in a clean plastic bin with a lid or in a
clean plastic zipper bag.
3. CLEANING INSTRUCTIONS
Unless otherwise instructed by your healthcare provider,
follow these sanitizing and cleaning instructions.
Do not boil or
wash tubing or
connector!
When sanitizing
parts, use enough
water to keep parts
aoat!
B7
B6
B3
B1
B2
B
B8
C
D
A
B4
B5
A3A1 A2
A4
E
= Retail
= Insurance