EasyManua.ls Logo

Larius 2 - User Manual

Larius 2
38 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P A I N T S P R A Y I N G E Q U I P M E N T
Painting
II 2 G c IIB T4
OPERATING AND
MAINTENANCE INSTRUCTIONS
ENGLISH
OPERATING AND
MAINTENANCE INSTRUCTIONS
Ed.
004
04 - 12

Questions and Answers

  • V
    vstephensonAug 8, 2025
    What to do if Larius 2 pressure lowers considerably when pressing the trigger?
    • R
      raymond94Aug 8, 2025
      If the pressure lowers considerably when pressing the trigger on your Larius Paint Sprayer, it could be due to a nozzle that is too big or worn. Replace it with a smaller one. Alternatively, the product may be too dense; if possible, dilute it.
  • S
    Stephanie NelsonAug 13, 2025
    Why Larius 2 pressure is normal but the product is not atomized?
    • A
      Anita Perez DVMAug 13, 2025
      If the pressure is normal but the product is not atomized with your Larius Paint Sprayer, the nozzle might be partially clogged. Try cleaning or replacing it. Also, check the flow regulator for the atomizing air, as there might be no atomizing air. If the product is too dense, dilute it if possible.
  • J
    Jeffrey StewartAug 18, 2025
    Why Larius Paint Sprayer equipment does not suck the product?
    • B
      Brian MooreAug 18, 2025
      If your Larius Paint Sprayer equipment isn't sucking the product, it might be due to a clogged suction filter. Clean or replace it. It could also be that the suction filter is too fine; replace it with a larger-mesh filter, or remove the filter if you're using very dense products. Another possibility is that the equipment is sucking air; check the suction pipe.
  • A
    Austin JohnsonAug 23, 2025
    What to do if Larius Paint Sprayer equipment sucks but does not reach the pressure desired?
    • K
      Katherine ColeAug 23, 2025
      If your Larius Paint Sprayer sucks but doesn't reach the desired pressure, it may be due to a lack of product. Add more product. Another cause could be that the equipment is sucking air; check the suction pipe. Finally, ensure that the circulation tap is closed.
  • E
    Erin MartinezAug 28, 2025
    Why Larius 2 Paint Sprayer atomization is imperfect?
    • E
      Eric SteeleAug 28, 2025
      If the atomization is imperfect with your Larius Paint Sprayer, the nozzle is likely worn. Replace it.
  • U
    uwilliamsSep 2, 2025
    How to fix leakage from the seal-tightening screw on Larius Paint Sprayer?
    • B
      Brittany YoungSep 2, 2025
      If there is leakage from the seal-tightening screw on your Larius Paint Sprayer, the gasket is likely worn or needs adjustment. Replace or adjust the gasket.

Summary

Safety Rules

Setting-Up

Operation

Cleaning After Spray Painting or Product Change

Routine Maintenance

Troubleshooting

Stainless Steel L2 Pump

Tank

Complete Trolley

Flow Regulator

Air Control Group on Trolley

Air Control Group Without Trolley

Filter with Circulation Stainless Steel Model

Filter with Circulation Aluminium Model

Suction Line Filter

Suction Tank Model

Wall-Mounted Model

Technical Features

Marking

Safety Instructions for Installations in Hazardous Areas

Larius 2 Specifications

General IconGeneral
Max Pressure3000 PSI
Max Flow Rate0.54 GPM
Power SourceElectric
TypeAirless
Motor Power0.5 HP
Voltage110-120V
Max Tip Size0.017 inches