Why is there no charging procedure possible for LawnMaster Lawn Mower?
If no charging procedure is possible for your LawnMaster Lawn Mower, it might be due to: * Contaminated battery contacts: Clean the battery contacts by inserting and removing the battery several times, or replace the battery. * Defective socket outlet, fuse, mains cable, or battery charger. * Faulty battery: Replace the battery.
What to do if LawnMaster robotic lawnmower is upside down?
If your LawnMaster robotic lawnmower is upside down, turn it the right way up and determine why it turned over, then rectify the cause.
What does it mean if LawnMaster Lawn Mower error indicator is yellow continuous?
A continuous yellow error indicator on your LawnMaster Lawn Mower suggests: * The lift sensor has been activated for 10 seconds: Remove and re-insert the isolator key, check for obstacles taller than 10 cm in the working area, and restart the mower. * The obstruction sensor has tripped 10 times in one minute: Remove and re-insert the isolator key, remove any obstacles, and check if the grass is too tall. If needed, mow the grass to below 60 mm with a conventional lawn mower, then restart the mower.
Why LawnMaster no charging procedure possible?
If no charging procedure is possible with your LawnMaster, the battery contacts may be contaminated; try cleaning them by inserting and removing the battery several times, or replace the battery. If this doesn't work, further assistance is needed.
Why LawnMaster ultrasonic indicator is yellow flashing?
A yellow flashing ultrasonic indicator on your LawnMaster mower suggests a communication issue with the camera. This can occur if it's too dark for the camera to function properly. Operate the mower during daylight hours only. You may also try removing and re-inserting the isolator key and restarting the mower.
Why is the LawnMaster VBRM16-01 Lawn Mower area of cut not large enough?
If the area your LawnMaster Lawn Mower cuts isn't large enough, consider these factors: * Height of cut too low: Increase the height of cut. * Grass is wet: Wait until the grass is dry. * Grass is dense: Increase the height of cut and cut more frequently. * Battery not fully charged: Charge the battery. * Lawn area too large: Recharge the battery and mow again or purchase an additional battery.
Why charge control LEDs do not light up after inserting the mains plug into the socket of LawnMaster VBRM16-01?
If the charge control LEDs don't light up after plugging in your LawnMaster Lawn Mower, check the following: * Mains plug not fully inserted: Ensure the mains plug is fully inserted into the socket outlet. * Defective socket outlet, mains cable, or battery charger. * Blown plug fuse: Check and replace the fuse in the plug.
What to do if the cutting blade is not rotating on my LawnMaster VBRM16-01?
If the cutting blade is not rotating while your LawnMaster Lawn Mower is switched on, it may be due to an obstruction. Remove the isolator key and the battery pack, then clear any obstructions. Also, check if the blade screw is loose and tighten it.
Why my LawnMaster VBRM16-01 fails to start?
If your LawnMaster Lawn Mower fails to start, check the following: ensure the isolator key is correctly installed, verify that the battery is properly installed, and make sure the battery is fully charged.
What to do if LawnMaster VBRM16-01 is cutting grass unevenly?
If your LawnMaster Lawn Mower is cutting grass unevenly, consider the following: * If the working area is too big, adjust the border protections to decrease it. Recharge the battery to mow the area twice or purchase an additional battery. * Check if blades are dull and replace all the blades and screws. * If the height of cut is too low, or the grass is too high, increase the height of cut. * Check underneath the mower for grass wrapped around the blade disc and clear as necessary.
General| Power Source | Battery |
|---|---|
| Cutting Width | 16 inches |
| Wheel Size | 6 inches |
| Engine Type | Electric |
| Cutting Height Adjustment | 5 positions |
To Next Page
