Lee Precision PRO 1000 - Cartridge Conversion Guide; Setup Components Chart

LEE PRECISION, INC. 4275 HWY. U HARTFORD WISCONSIN 53027
www.leeprecision.com
To convert the Pro- from a one cartridge to another, you will need the proper shell plate, primer trough and primer pin (  primer
attachment) and appropriate Lee reloading die set. The chart below shows proper configuration with catalog numbers. Identify your current press
configuration by cartridge. The chart will list which components shipped with your press (primer feed, shell plate) Then check the cartridge you wish to
load, to see which components match with your current press configuration. Order any components that do not match (primer feed and shell plate)
CARTRIDGE
SHELL PLATE SHELL PLATE PRIMER FEED PLATE SLIDER
NUMBER ONLY FEED HOLE SIZE BLOCK
 Luger   SMALL SMALL  PRO AUTO-DISK
 Mauser   SMALL SMALL  PRO AUTO-DISK
 Tokarev   LARGE SMALL  PRO AUTO-DISK
 ACP   SMALL SMALL  AUTO-DRUM
 S&W Long   SMALL SMALL  AUTO-DRUM
 H&R MAG   FED   SMALL SMALL  AUTO-DRUM
mm Luger   SMALL SMALL  AUTO-DRUM
mm Makarov   SMALL SMALL  AUTO-DRUM
   SMALL N/A N/A  AUTO-DRUM
 Sig   SMALL SMALL  PRO AUTO-DISK
 Super   SMALL SMALL  PRO AUTO-DISK
 S&W   SMALL SMALL  AUTO-DRUM
 Auto   SMALL SMALL  AUTO-DRUM
 SPL &  MAG   SMALL SMALL RISER  AUTO-DRUM
 ACP   SMALL SMALL  PRO AUTO-DISK
 Short/Long COLT   SMALL SMALL  AUTO-DRUM
 S&W   SMALL SMALL  AUTO-DRUM
mm Auto   LARGE SMALL  PRO AUTO-DISK
 Mag   LARGE LARGE RISER  AUTO-DRUM
 SPL &  MAG   LARGE LARGE RISER  PRO AUTO-DISK
 Cor Bon   LARGE LARGE  AUTO-DRUM
M   SMALL SMALL RISER  AUTO-DRUM
 Russian   LARGE LARGE RISER  AUTO-DRUM
- WIN   LARGE LARGE RISER  PRO AUTO-DISK
 Casull   SMALL LARGE RISER  AUTO-DRUM
 ACP   SMALL OR LARGE LARGE  PRO AUTO-DISK
 Auto Rim   LARGE LARGE  PRO AUTO-DISK
 Colt   LARGE LARGE RISER  AUTO-DRUM
 Schofield   LARGE LARGE RISER  PRO AUTO-DISK
 GAP   LARGE LARGE  PRO AUTO-DISK
 WIN MAG   LARGE LARGE RISER  AUTO-DRUM
 S&W   LARGE LARGE RISER  AUTO-DRUM
 Action Express   LARGE N/A N/A  (LUBE REQ.) AUTO-DRUM
 REM   SMALL SMALL RISER  (LUBE REQ.)  AUTO-DRUM
 x    LARGE SMALL RISER  (LUBE REQ.)  AUTO-DRUM
 REM   SMALL SMALL RISER  (LUBE REQ.)  AUTO-DRUM
 SOCOM   LARGE N/A N/A  (LUBE REQ.) AUTO-DRUM
N/A = Not available LUBE REQ. = # 90006 LEE resizing lubricant required PRO AUTO-DISK # 90429 AUTO-DRUM # 90811
RELOADING DIES
CHARGING
DIE
POWDER MEASURE
8
Te LeeGuarane
lee reloading products are guaranteed not to wear out or break from normal use for two full years or
they will be re paired or replaced at no charge if returned to the factory. Any Lee product of current
manufacture, regardless of age or condition, will be recon di tioned to new, including a new guarantee, if
re turned to the factory with payment equal to half the current retail price.
CHANGING CARTRIDGE SETUP
PREVIOUS PRO 1000 OWNER?
Your previously purchased shell plates will work on this new
press if they have three through holes, and your carrier is the
“NEW” version.
OLD
NEW
To utilize your old shell plates,
your press alignment pin must be
removed. Remove the press from
your bench, use a plastic mallet and
drive the pin through the base.
Assembled as
SMALL feed
plate
Bolt and nuts are
adjacent to small
through hole and
the small plug.
small
hole
large
hole
small plug removed
Assembled as
LARGE feed
plate
small plug
installed
storage spot for
small plug