Lenze EVS9323EP User Manual

Function library
Positioning control
3.4.11 Program operation
3−73
l
EDSVS9332P−EXT DE 2.0
3.4.11.2 Status of the program control
The actual state of the program control is displayed via the status outputs of the POS function block
and the positioning status (C1283).
Status outputs
Update conditions of the status outputs "RUNNING", POS−STARTED", POS−STOPPED",
POS−ENDED", POS−RESETED" and the positioning status in code C1283:
– The power stage is supplied (DCTRL−RDY=1)
– The drive is enabled (DCTRL−CINH=0)
– No fault applies (DCTRL−TRIP=0, DCTRL−FAIL−QSP=0)
– Quick stop (QSP) is not activated (MCTRL−QSP−OUT=0)
– Manual operation is not activated (POS−MANUAL=0, C1280.B4=0)
9300POS027
S t a r t = L
P r o g r a m m e n d e
R e s e t = L , S t o p = L , S t a r t =
R e s e t = L
S t o p = H
R e s e t = L
S t o p = L
k e i n e U n t e r b r .
R e s e t = L
P O S - V S E T = 0
R e s e t = H
S t o p = L
U n t e r b r e c h u n g
R e s e t = L
S t o p = H
U n t e r b r e c h u n g
R U N N I N G = 0
S T A R T E D = 0
S T O P P E D = 0
E N D E D = 1
R E S E T E D = 0
R U N N I N G = 0
S T A R T E D = 0
S T O P P E D = 0
E N D E D =
1
R E S E T E
D = 1
R U N N I N G = 1
S T A R T E D = 1
S T O P P E D = 0
E N D E D = 0
R E S E T E D = 0
R U N N I N G = 0
S T A R T E D = 0
S T O P P E D = 1
E N D E D = 0
R
E S E T E D = 0
R U N N I N G = 0
S T A R T E D = 1
S T O P P E D = 0
E N D E D = 0
R E S E T E D = 0
C 1 2 8 3 = " P r g - R e s e t "
C 1 2 8 3 = " G e s t a r t e t " C 1 2 8 3 = " G e s t o p p t "
C 1 2 8 3 = " G e s t a r t e t - b r e a k "
R e s e t = L
S t o p = H
S t a r t =
R e s e t = L , S t o p = L , S t a r t =
R e s e t = H
C 1 2 8 3 = " S t a r t b e r e i t "
C 1 2 8 3 = " P r o g r a m m e n d e "
R e s e t = H
Fig. 3−27 Status machine of program control
Status "Ready to start"
l Program control is ready to start but not started yet.
l Status output POS−ENDED = HIGH,
l Positioning status (C1283) = Ready to start",
l Current PS No. (POS−ACT−PS−NO) = 0 (program end)
Status Started"
l Program has been started, the positioning program is running.
l Status output POS−STARTED = HIGH and
l Status output POS−RUNNING=HIGH (for firmware version ³ 2.5)
l Positioning status (C1283) = Started",
or Started−rem", if C1280.B0 = 1 (GDC control),
or Started−dig", if input POS−PRG−START = HIGH.

Lenze EVS9323EP Specifications

General

Brand	Lenze
Model	EVS9323EP
Category	Controller
Language	English