Lenze I51AE175B - Page 466

Address Designaon Default seng Category Data type Factor A M
0x2631:025
(P400.25)
Funcon list: Acvate MOP setpoint Not connected [0] general U8 1 P -
0x2631:026
(P400.26)
Funcon list: Acvate segment setpoint (bit 0) Not connected [0] general U8 1 P -
0x2631:027
(P400.27)
Funcon list: Acvate segment setpoint (bit 1) Not connected [0] general U8 1 P -
0x2631:028
(P400.28)
Funcon list: Acvate segment setpoint (bit 2) Not connected [0] general U8 1 P -
0x2631:029
(P400.29)
Funcon list: Acvate segment setpoint´(bit 3) Not connected [0] general U8 1 P -
0x2631:030
(P400.30)
Funcon list: Run/abort sequence Not connected [0] general U8 1 PC -
0x2631:031
(P400.31)
Funcon list: Start sequence Not connected [0] general U8 1 PC -
0x2631:032
(P400.32)
Funcon list: Next sequence step Not connected [0] general U8 1 PC -
0x2631:033
(P400.33)
Funcon list: Pause sequence Not connected [0] general U8 1 PC -
0x2631:034
(P400.34)
Funcon list: Suspend sequence Not connected [0] general U8 1 PC -
0x2631:035
(P400.35)
Funcon list: Stop sequence Not connected [0] general U8 1 PC -
0x2631:036
(P400.36)
Funcon list: Abort sequence Not connected [0] general U8 1 PC -
0x2631:037
(P400.37)
Funcon list: Acvate network control Not connected [0] general U8 1 P -
0x2631:039
(P400.39)
Funcon list: Acvate ramp 2 Not connected [0] general U8 1 P -
0x2631:040
(P400.40)
Funcon list: Load parameter set Not connected [0] general U8 1 PC -
0x2631:041
(P400.41)
Funcon list: Select parameter set (bit 0) Not connected [0] general U8 1 PC -
0x2631:042
(P400.42)
Funcon list: Select parameter set (bit 1) Not connected [0] general U8 1 PC -
0x2631:043
(P400.43)
Funcon list: Acvate fault 1 Not connected [0] general U8 1 P -
0x2631:044
(P400.44)
Funcon list: Acvate fault 2 Not connected [0] general U8 1 P -
0x2631:045
(P400.45)
Funcon list: Deacvate PID controller Not connected [0] general U8 1 P -
0x2631:046
(P400.46)
Funcon list: Set process controller output to 0 Not connected [0] general U8 1 P -
0x2631:047
(P400.47)
Funcon list: Inhibit process controller I-component Not connected [0] general U8 1 P -
0x2631:048
(P400.48)
Funcon list: Acvate PID inuence ramp Constant TRUE [1] general U8 1 P -
0x2631:049
(P400.49)
Funcon list: Release holding brake Not connected [0] general U8 1 PC -
0x2631:050
(P400.50)
Funcon list: Select sequence (bit 0) Not connected [0] general U8 1 PC -
0x2631:051
(P400.51)
Funcon list: Select sequence (bit 1) Not connected [0] general U8 1 PC -
0x2631:052
(P400.52)
Funcon list: Select sequence (bit 2) Not connected [0] general U8 1 PC -
0x2631:053
(P400.53)
Funcon list: Select sequence (bit 3) Not connected [0] general U8 1 PC -
0x2631:054
(P400.54)
Funcon list: Posion counter reset Not connected [0] general U8 1 P -
* Default seng depending on the size. Firmware version 05.00.00.00
Appendix
Parameter aribute list
466