Lenze L-force HighLine C 8400 Series

Motor Selection/Motor Data132
- Selecting a Motor from the Motor Catalogue in the "Engineer135
- Automatic Motor Data Identification137
Selecting the Control Mode142
- Selection Help146
Defining Current and Speed Limits147
V/F Characteristic Control149
(Vfcplus)150
- Parameterisation Dialog/Signal Flow151
- Basic Settings153
  - Defining the V/F Characteristic Shape154
  - Defining Current Limits (Imax Controller)155
- Optimising the Control Mode156
- Remedies for Undesired Drive Behaviour168
V/F Characteristic Control - Energy-Saving (Vfcpluseco)169
- Parameterisation Dialog/Signal Flow170
- Comparison of Vfcpluseco - Vfcplus172
- Basic Settings173
- Optimising the Control Mode174
- Remedies for Undesired Drive Behaviour177
V/F Control (Vfcplus + Encoder)179
- Parameterisation Dialog/Signal Flow179
- Basic Settings181
  - Parameterising the Slip Regulator182
Sensorless Vector Control185
(Slvc)185
- Parameterisation Dialog/Signal Flow186
- Types of Control188
- Limitation188
  - Speed Control with Torque189
  - Torque Control with Speed Limitation189
- Basic Settings190
- Optimising the Control Mode191
- Remedies for Undesired Drive Behaviour200
Sensorless Control for Synchronous Motors (SLPSM)201
- Parameterisation Dialog/Signal Flow203
- Types of Control206
- Basic Settings207
- Optimising the Control Mode209
  - Optimise Current Controller210
Controller210
- Optimise Speed Controller211
- Optimise Response to Setpoint Changes and Determine Mass Inertia215
- Pole Position Identification Without Motion217
Servo Control (SC)219
- Parameterisation Dialog/Signal Flow220
- Types of Control223
- Basic Settings225
  - Parameterising the Encoder/Feedback System226
- Optimising the Control Mode227
  - Optimise Current Controller228
Controller228
- Optimise Speed Controller229
- Optimise Response to Setpoint Changes and Determine Mass Inertia233
- Setting the Current Setpoint Filter (Band-Stop Filter)235
- Adapting the Max. Acceleration Change (Jerk Limitation)236
- Slip Calculation from Motor Equivalent Circuit Diagram Data237
- Optimising the Behaviour in the Field Weakening Range238
Parameterisable Additional Functions243
- Selection of Switching Frequency243
- Operation with Increased Rated Power246
- Correction of the Stator Leakage Inductance248
- Flying Restart Function250
- DC-Injection Braking253
  - Automatic DC-Injection Braking (Auto-DCB)254
  - Manual DC-Injection Braking (DCB)254
- Slip Compensation258
- Oscillation Damping260
- Phase Sequence Reversal for Correcting Misconnected UVW Motor Phases264
- Field Weakening for Synchronous Motors265
Encoder/Feedback System269
- Parameterising Digital Inputs as Encoder Inputs272
- Encoder Evaluation Method273
- Generation of the Actual Speed Value274
- Encoder with HTL Level at DI1/DI2275
- Encoder with HTL Level at DI6/DI7277
Position Control/Additive Speed Specification278
Braking Operation/Brake Energy Management279
Management280
- Setting the Voltage Source for Braking Operation281
- Selecting the Response to an Increase of the DC-Bus Voltage282
  - Inverter Motor Brake284
- Avoiding Thermal Overload of the Brake Resistor287
Monitoring288
- Device Overload Monitoring289
- (Ixt)289
- Motor Load Monitoring (I2Xt)290
- Motor Temperature Monitoring (PTC)292
- Brake Resistor Monitoring (I2Xt)293
- Motor Phase Failure Monitoring295
- Motor Phse Error Monitoring before Operation296
- Mains Phase Failure Monitoring298
- Maximum Current298
  - Monitoring298
- Maximum Torque Monitoring299
- Motor Speed Monitoring299
- Encoder Open-Circuit Monitoring300
Internal Interfaces | System Block "Ls_Motorinterface301
Internal Status Signals | System Block "Ls_Devicemonitor307

6 O Terminals309

7 Technology Applications358

8 Basic Drive Functions (MCK)450

9 Diagnostics & Error Management559

10 System Bus "CAN on Board613

11 Fieldbus Interface686

12 Synchronisation of the Internal Time Base693

Internal Interfaces | System Block "Ls_Syncmanagement693

13 Parameter Change-Over694

14 Parameter Reference.703

15 Working with the FB Editor1010

Reconfiguring the Predefined Interconnection1030

16 Function Library1061

17 Index1365

Brand	Lenze
Model	L-force HighLine C 8400 Series
Category	Controller
Language	English

Lenze L-force HighLine C 8400 Series - User Manual

Table of Contents

Lenze L-force HighLine C 8400 Series Specifications

Related product manuals