LevelOne WAP-6121 User Manual (English)

Other manuals for LevelOne WAP-6121

Questions and Answers:

B
Brittany JohnstonAug 11, 2025
What to do if I can't access my LevelOne WAP-6121 Wireless Access Point through the web page?
- L
  lisamcintyreAug 11, 2025
  First, verify that your computer and the LevelOne Wireless Access Point have IP addresses within the same networking segment. You can test the Wireless Access Point connectivity by opening the command prompt (Start > Run > cmd) and using the command 'ping 192.168.188.253'. If there are connectivity issues, reset the Wireless Access Point. Ensure that the IP address 192.168.188.253 is not being used by another device on the network. Check the computer and cable; it's recommended to use a 10/100M UTP unshielded cable. Also, clear any Arp bindings by using the command 'arp -d' in the command prompt. Finally, clear your web browser's temporary files and cache.
H
hallkarenAug 15, 2025
What to do if my LevelOne Wireless Access Point won't connect to the AP and the status shows unconnected?
- T
  Tonya MarksAug 15, 2025
  Try scanning for available wireless networks again. Ensure that the wireless standard of your LevelOne Wireless Access Point is correct (2.4Ghz signal should connect to a 2.4Ghz network, and a 5.8Ghz signal should connect to a 5.8Ghz network). Verify that the security settings and passwords match between the Wireless Access Point and the AP. The signal strength of the AP might be too weak; it should be more than -75dBm.
M
mclaughlinjosephAug 20, 2025
How do I reset my LevelOne WAP-6121?
- A
  Alan SingletonAug 20, 2025
  To reset the LevelOne Wireless Access Point, press and hold the “Reset” button for more than 15 seconds after powering it on. The Wireless Access Point will then restart and restore to its factory default settings.
P
Paula NicholsonAug 26, 2025
Why can't my computer share the internet even though the LevelOne WAP-6121 connection is successful?
- R
  richardcuevasAug 26, 2025
  Check your computer's IP address and DNS settings. If your computer is set to obtain an IP address automatically, ensure that your network card is configured to do so. If you are using a static IP address, contact your ISP to confirm you are using the correct IP address and DNS address.
P
phillip42Aug 30, 2025
What to do if my LevelOne WAP-6121 can't be found when scanning for wireless networks?
- T
  Thomas ValdezAug 30, 2025
  Try scanning several times. If you are using a 5Ghz network, ensure that a 5Ghz signal is available. Reset the LevelOne Wireless Access Point and try scanning again after it restarts.
C
Cassandra SalasSep 4, 2025
Why is the SYS indicator light off on my LevelOne WAP-6121?
- B
  Brittany WilsonSep 5, 2025
  Make sure the PoE module connection is correct. The POE Port should connect to the LevelOne Wireless Access Point, and the LAN port should connect to your computer.

LevelOne WAP-6121 Specifications

General

Frequency Band	2.4 GHz
Maximum Data Rate	300 Mbps
Antenna Type	Internal
Weight	250 g
Operating Temperature	0°C to 40°C
Storage Temperature	-20°C to 70°C
Operating Humidity	10% to 90% non-condensing
Wireless Standards	IEEE 802.11n
Antenna	2 x 3 dBi
Ports	1 x 10/100 Mbps Ethernet
Security	WEP, WPA, WPA2
Power Supply	12V DC
Storage Humidity	5% ~ 95% (Non-condensing)