Leviton QuickPort Duplex 106

To Next Page

QuickPort

Field-Configurable Connector Housings

Component

Specifications

3880-DIN

QuickPort

Field-Configurable Connector Housings

Part Numbers

41087-xxP

2222 – 222nd St. SE • Bothell, WA 98021 USA • Tel: 1-800-722-2082 / 1-425-485-4288 • Fax: 1-425-483-5270 • Int'l Fax: 1-425-485-9170 • GSA# GS-35F-4785G

For Applications Engineering Support – Call 1-425-485-4288; in USA call 1-800-722-2082

Spec sheets and updates are also available at www.levitonvoicedata.com.

NEMA-Style Housings

Field-configurable housings in several NEMA styles that accept all

individual QuickPort

snap-in modules. Use to support multime-

dia applications where a flush-mount electrical-wallplate look is

desired, or where there will be multiple devices—or a combina-

tion of electrical and voice/data devices—under a multi-gang

wallplate.

APPLICATION

• Use where an electrical-outlet look & flush-mounting are impor-

tant.

• Fits most locations where NEMA duplex opening exists (includ-

ing floor monuments, access floor boxes, power poles, poke-

through fixtures, etc.).

• Gangable in single or multiple gangs.

• If ganged with electrical devices, a barrier box must be used.

• The TR Plus accommodates IEEE 802.5 token ring connectors.

• Put blanks (41084-B*B) in unused ports for future expansion.

• Specify port identification method (colored modules, designa-

tion labels, and custom silkscreening are available). To ID ports,

use different colored jacks for each application (full selection of

TIA/ EIA-606 compatible colors—13 available), or Leviton's pre-

printed Port Designation Labels. (Part #: 41080 LXB)

UNIQUE FEATURES

• Four color choices (Ivory, White, Gray, Black).

• Fits within minimum NEMA openings.

• Compatible with all individual QuickPort modules.

• Brass threaded insert for wallplate screw facilitates installation.

• The TR Plus version accommodates IEEE 802.5 token ring

connectors in a NEMA-style housing.

• Narrow module width allows high port density in a small area.

• The Quad 106 features a built-in termination station.

DESIGN CONSIDERATIONS

Meets or exceeds all applicable standards: UL Listed; CSA

Certified; Complies with NEC

Article 800 and TIA/EIA-568-A;

and meets FCC Part 68.

STANDARDS COMPLIANCE

PHYSICAL SPECIFICATIONS

Capacity:

Materials:

Dimensions:

Quad 106: 1-4 ports. Duplex 106: 1-2 ports

TR Plus: 1-2 ports w/token ring connector capability

High-impact, fire-retardant plastic rated UL 94V-0

Quad 106: 1.3"W x 4.1"H x 1.178" D (loaded)

Duplex 106: 1.5"W x 4.1"H x 1.2" D (loaded)

TR Plus 106: 1.5"W x 4.1"H x 1.2" D (loaded)

TYPICAL SPECIFICATION

The workstation jack/connector housing shall be a field-configurable

NEMA-style housing that mounts flush in standard NEMA openings,

and under standard duplex electrical wallplates in single or multiple

gangs. It should provide ports which are field-configurable with a vari-

ety of simplex snap-in jacks/modules. Must be constructed of high-

impact, fire-retardant plastic rated UL 94V-0, and be UL Listed, CSA

Certified, and compliant with FCC Part 68 and TIA/EIA-568-A specifi-

cations. Colors, configurations and related wallplates to be specified

per schedule on plan. The manufacturer shall provide a one-year

limited product warranty and 15 year product performance guaran-

tee. The manufacturer shall provide a lifetime warranty against

defects in material and workmanship and an application guarantee

when installed as part of a certified system.

INSTALLATION NOTES

• Terminate jacks/modules, then snap them into housing from

the rear; housing screws to box, and NEMA plate screws to the

housing.

• Detailed installation instructions are included in the carton.

• Break off "T" arms for floor monument installation.

• The Quad 106 “Termination Station” (built-in termination aid)

stabilizes jacks during punchdown.

WARRANTY INFORMATION

• One-year limited product warranty and 15-year performance

guarantee are standard.

• Product and performance warranties are extended to a Lifetime

as part of Leviton’s Certified Cabling System.

See ELECTRONIC FILES for CAD files (.DXF, .DWG, MS-DOS.EPS) on disk

For ELECTRONIC Typical Specs see (.TXT) file on disk.

Quad 106

Duplex 106

Need help?

Do you have a question about the Leviton QuickPort Duplex 106 and is the answer not in the manual?

Summary

QuickPort Field-Configurable Connector Housings

Application

Supports multimedia applications requiring flush-mount electrical-wallplate look with multiple devices.

Standards Compliance

Meets or exceeds UL, CSA, NEC Article 800, TIA/EIA-568-A, and FCC Part 68 standards.

Physical Specifications

Details capacity, materials, and dimensions for Quad 106, Duplex 106, and TR Plus models.

Design Considerations

Guidance on flush-mounting, gangability, barrier boxes, and port identification methods.

Unique Features

Highlights color choices, NEMA compatibility, module compatibility, and termination station.

Typical Specification

Defines workstation jack/connector housing requirements, materials, and certifications.

Installation Notes

Provides instructions for terminating jacks, mounting, and breaking off arms.

Warranty Information

Outlines product warranty periods and extended lifetime warranty options.

Dimensional Line Art

QuickPort Quad 106 Flush Mount Jack

Diagrams showing front and side views with dimensions for the Quad 106 jack.

QuickPort Duplex Flush Mount Jack

Diagrams showing front and side views with dimensions for the Duplex jack.

Part Number

QuickPort 12-Port Surface Mount Housing

Lists part numbers for Quad 106, Duplex 106, and TR Plus housings.