To Next PageTo Next PageWhat to do if Lexmark T630 operator panel is blank?
If the operator panel of your Lexmark printer displays only diamonds or is blank, turn the printer off, wait about 10 seconds, and turn the printer on. After turning the printer on, 'Performing Self Test' should appear on the operator panel, and when the test is completed, 'Ready' should be displayed.
How to fix Lexmark T630 Printer when print media misfeeds?
If your Lexmark printer is misfeeding or feeding multiple sheets, ensure the print media meets the printer's specifications. Flex the print media before loading. Make sure the print media is loaded correctly, and the width and length guides are adjusted properly. Do not overfill the print media sources or force print media into the multipurpose feeder. Remove any curled print media and load the recommended print side correctly. Try loading less print media, turning it over, and avoiding mixing different types or reams of print media. Remove the top and bottom sheets of a ream before loading, and only load a print media source when it is empty.
Why is the print too light on my Lexmark T630?
If the print from your Lexmark printer is too light, the toner may be low. Remove the cartridge, grip the handles with both hands, point the cartridge arrows downward, and shake it back and forth to utilize the remaining toner. Reinstall the cartridge and press Go. You can also change the Toner Darkness setting in the Quality Menu. If printing on an uneven surface, adjust the Paper Weight and Paper Texture settings in the Paper Menu, and verify that you are using the correct print media.
What to do if Lexmark Printer toner smears?
If the toner smears or the print comes off the page when using your Lexmark printer, and you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper Menu. Also, verify that the print media is within the printer specifications.
Why is my Lexmark Printer not duplexing pages?
If your Lexmark printer is not duplexing pages, ensure that 'Duplex' is selected in both the Finishing Menu and in the printer driver. Also, make sure you have enough printer memory installed.
Why toner fog appears on the page from Lexmark T630?
If toner fog or background shading appears on the page when using your Lexmark printer, check the print cartridge to make sure it is installed correctly. If the problem continues, change the print cartridge. If the problem still continues, change the charge roll.
How to fix consistent misfeeds in Lexmark T630 Printer drawer?
If you experience consistent misfeeds or jams in the drawer of your Lexmark printer, try flexing the paper and turning the print media over. Check that the drawer is properly installed, the print media is loaded correctly and is not damaged, meets specifications, and that the guides are positioned correctly for the selected print media size.
How to fix Lexmark T630 Printer when envelope misfeeds?
If envelope misfeeds or multiple feeds occur when using your Lexmark printer, remove the stack of envelopes from the envelope feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the envelope feeder.
Why does toner appear on the back of the printed page from my Lexmark Printer?
If toner appears on the back of the printed page from your Lexmark printer, it is because toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer upper front door to run the printer setup cycle and clean the transfer roll.
Why is part of the page printed in black from my Lexmark T630 Printer?
If part or all of the page is printed in black when using your Lexmark printer, check the print cartridge to see if it is installed correctly. Also, if the charge roll has been replaced, verify that it is installed correctly.
General| Print Technology | Laser |
|---|---|
| Print Speed | Up to 35 ppm |
| Resolution | 1200 x 1200 dpi |
| Operating System Compatibility | Windows, Mac, Linux, UNIX |
| Connectivity | Parallel, USB |
| First Print Out Time | Less than 8.5 seconds |
| Duplex Printing | Optional |
| Media Sizes | A4, A5, Letter, Legal, Executive, Folio |
| Paper Capacity | 100-sheet multipurpose feeder |
| Weight | 43 lbs (19.5 kg) |
