To Next Page
H
hugheshollySep 18, 2025
Why does the elevator tray lower unexpectedly on Lexmark Printer?
- RricejohnSep 19, 2025
Check to see if your Lexmark printer is out of print media or has a jam.
Why does the elevator tray lower unexpectedly on Lexmark Printer?
Check to see if your Lexmark printer is out of print media or has a jam.
How to fix Lexmark T630 Printer when print media misfeeds?
If your Lexmark printer is misfeeding or feeding multiple sheets, ensure the print media meets the printer's specifications. Flex the print media before loading. Make sure the print media is loaded correctly, and the width and length guides are adjusted properly. Do not overfill the print media sources or force print media into the multipurpose feeder. Remove any curled print media and load the recommended print side correctly. Try loading less print media, turning it over, and avoiding mixing different types or reams of print media. Remove the top and bottom sheets of a ream before loading, and only load a print media source when it is empty.
Why is the print too light on my Lexmark T630?
If the print from your Lexmark printer is too light, the toner may be low. Remove the cartridge, grip the handles with both hands, point the cartridge arrows downward, and shake it back and forth to utilize the remaining toner. Reinstall the cartridge and press Go. You can also change the Toner Darkness setting in the Quality Menu. If printing on an uneven surface, adjust the Paper Weight and Paper Texture settings in the Paper Menu, and verify that you are using the correct print media.
What to do if Lexmark Printer toner smears?
If the toner smears or the print comes off the page when using your Lexmark printer, and you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper Menu. Also, verify that the print media is within the printer specifications.
What do service messages mean on Lexmark Printer?
A service message indicates a printer failure that may require service. Turn the Lexmark printer off, wait about 10 seconds, and then turn the printer on. If the error recurs, write down the error number, the problem, and a detailed description.
How to fix short paper error on Lexmark Printer?
Make sure the size selector knob is set to the correct print media size.
How to fix jagged edges on characters from Lexmark Printer?
If characters have jagged or uneven edges when printed from your Lexmark printer, change the Print Resolution setting in the Quality Menu to 600 dpi or 1200 dpi. If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software application.
Why are there unexpected page breaks on my Lexmark T630 Printer?
If page breaks occur in unexpected places when using your Lexmark printer, check the Print Timeout setting in the Setup Menu and increase the setting.
How to fix Lexmark T630 Printer when envelope misfeeds?
If envelope misfeeds or multiple feeds occur when using your Lexmark printer, remove the stack of envelopes from the envelope feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the envelope feeder.
Why does toner appear on the back of the printed page from my Lexmark Printer?
If toner appears on the back of the printed page from your Lexmark printer, it is because toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer upper front door to run the printer setup cycle and clean the transfer roll.
General| Print Technology | Laser |
|---|---|
| Print Speed | Up to 35 ppm |
| Resolution | 1200 x 1200 dpi |
| Operating System Compatibility | Windows, Mac, Linux, UNIX |
| Connectivity | Parallel, USB |
| First Print Out Time | Less than 8.5 seconds |
| Duplex Printing | Optional |
| Media Sizes | A4, A5, Letter, Legal, Executive, Folio |
| Paper Capacity | 100-sheet multipurpose feeder |
| Weight | 43 lbs (19.5 kg) |
