Why are there unexpected page breaks on my Lexmark T630 Printer?
If page breaks occur in unexpected places when using your Lexmark printer, check the Print Timeout setting in the Setup Menu and increase the setting.
How to fix jagged edges on characters from Lexmark Printer?
If characters have jagged or uneven edges when printed from your Lexmark printer, change the Print Resolution setting in the Quality Menu to 600 dpi or 1200 dpi. If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software application.
What to do if Lexmark Printer is connected to USB but will not print?
If your Lexmark printer is connected to the USB port but will not print, make sure you are using Windows 98, Windows 2000, Windows Me, or another USB-capable operating system supported by Lexmark.
Why menu settings changed from Lexmark Printer operator panel have no effect?
If changing menu settings from the operator panel of your Lexmark printer has no effect, it is because the settings in the software application, the printer driver, or the printer utilities are overriding the settings made from the operator panel. Change the menu settings from the printer driver, the printer utilities, or the software application instead of the operator panel. Alternatively, disable the settings in the printer driver, the printer utilities, or the software application so you can change settings from the operator panel.
What to do if the Lexmark T630 Printer job did not print?
Before sending a print job, ensure that 'Ready' is displayed on the operator panel. If it is not, press 'Go' to return to the 'Ready' state. Also, verify that the printer is using the correct printer language and that you are using the correct printer driver. Ensure that the print media is loaded in the printer. Press 'Go' to return to 'Ready'. Finally, check that the parallel, serial, Ethernet, or USB cable is firmly plugged in at the back of the printer, using the correct cable (IEEE 1284-compliant parallel cable is recommended). If connected through a switch box, try a direct connection. Also, verify that the correct print media size is selected through the operator panel, in the printer driver, or in the software application and that PCL SmartSwitch and PS SmartSwitch are set to On.
How to fix consistent misfeeds in Lexmark T630 Printer drawer?
If you experience consistent misfeeds or jams in the drawer of your Lexmark printer, try flexing the paper and turning the print media over. Check that the drawer is properly installed, the print media is loaded correctly and is not damaged, meets specifications, and that the guides are positioned correctly for the selected print media size.
What to do if Lexmark T630 operator panel is blank?
If the operator panel of your Lexmark printer displays only diamonds or is blank, turn the printer off, wait about 10 seconds, and turn the printer on. After turning the printer on, 'Performing Self Test' should appear on the operator panel, and when the test is completed, 'Ready' should be displayed.
How to fix Lexmark T630 Printer when envelope misfeeds?
If envelope misfeeds or multiple feeds occur when using your Lexmark printer, remove the stack of envelopes from the envelope feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the envelope feeder.
Why is part of the page printed in black from my Lexmark T630 Printer?
If part or all of the page is printed in black when using your Lexmark printer, check the print cartridge to see if it is installed correctly. Also, if the charge roll has been replaced, verify that it is installed correctly.
Why does toner appear on the back of the printed page from my Lexmark Printer?
If toner appears on the back of the printed page from your Lexmark printer, it is because toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer upper front door to run the printer setup cycle and clean the transfer roll.
General| Print Technology | Laser |
|---|---|
| Print Speed | Up to 35 ppm |
| Resolution | 1200 x 1200 dpi |
| Operating System Compatibility | Windows, Mac, Linux, UNIX |
| Connectivity | Parallel, USB |
| First Print Out Time | Less than 8.5 seconds |
| Duplex Printing | Optional |
| Media Sizes | A4, A5, Letter, Legal, Executive, Folio |
| Paper Capacity | 100-sheet multipurpose feeder |
| Weight | 43 lbs (19.5 kg) |
To Next Page
