7
ENG
ENGLISH
INSTALLATION MENU
channel, since the TV would always select that channel
when it is turned On. When set to No, the TV starts on
the channel it was on before turning off.
Aux Source Setting
The Aux Source Setting feature will enable or
disable each external input. This data will be
retained in non-volatile memory and will survive a
power loss.
Minimum Volume
This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down control. In
this way, for example, someone cannot set the volume
too low to hear. The value range is from 0 to 100 —
change values with ADJ Left/Right arrow. The factory
default is 0, which provides the full range of volume
control, if item 009 MAX VOLUME is also set to 100. It
may be best to set the same value on every TV.
NOTE
: The minimum volume level cannot have a value
setting higher than the MAX VOLUME level (described
below).
Maximum Volume
This function determines the maximum volume
level allowable with the VOLUME (VOL) Up/Down
controls. In this way, for example, someone can not
set the volume level high enough to disturb others.
The value range is 0 to 100, with 100 as the default,
which gives the user the full range of volume control,
if item 008 MIN VOLUME is also set at 0. Change
values with ADJ Left/Right arrow keys. It may be
best to set the same value on every TV.
NOTE
: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(described previously).
Start Volume
This function allows the Installer to determine
the initial volume level setting when the TV is
turned ON. This feature is useful for an in-house
information channel, since the TV would always
select that Volume level when it is turned on. The
range of values are 0 - 100. If No is selected, the
current volume level will be retained in memory
when the TV is turned Off. At TV turn On, Volume
level is automatically set to the previous level.
Setting is retained in non-volatile memory.
Power Management
Determines hours of no activity before automatic
shutoff. The POWER MANAGE function is for
saving energy. If set to No, Power Manage is
disabled. Settings range from 1 ~ 7, representing
the hours that the unit will remain On, unless
there has been activity from either the control
panel or remote control. Setting is retained in non-
volatile memory.
Key Management
If set to 1, key defeat prevents the end user from
accessing the on-screen menus with the display
front panel, and < or > button do not function. If
set to 0, those keys do function.
Note: The menus can always be accessed by
pressing SETTINGS button on the remote.
Key management when enabled determines
the level of control that the guest has over the
television. Key management has five modes:
(default is ‘0’)
0 = Television is unrestricted and responds to
all commands.
1 = Key defeat ”prevents the television from
responding to “SETTINGS”key presses on
the front panel.
2 = “Key Lock ”prevents the television from
responding to any front panel key press.
3 = “System provider”mode allows access to
the menu system from the front panel or
remote control but access is controlled as
follows
* Accessible items on the menu system
- Main/PIP input select screens
- Sleep Timer
- Aspect Ratio
- Closed Caption
- Full access “Lock”
Q.menu, related to “Setup Menu”, is not
accessible either.
4 = “Key defeat” prevents the TV from
responding to a “SETTINGS” button
pressed on the front panel and remote
control.
5 = “No access Remote/Front panel” prevents
the TV from responding to any button
pressed on the front panel and remote
control.
NOTE
: You must set the Auto Off option to
off in the Time menu to prevent the TV set
from being turned off automatically.
Setting is retained in non-volatile memory.
Factory Reset
Set to 0 for normal.
Set to 1 to load presets to all of the previous item
settings and exit menu.
WARNING: Setting this to 1 will reload the factory
defaults.
Setting is retained in non-volatile memory.
To Next Page
Loading...
Need help?
General
