LG 32LB560B - MAKING CONNECTIONS; Connecting to Antenna or Cable

- 14 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
5.1.6. Reference
(White Balance Adj. coordinate and color
temperature)
▪ Luminance: 204 Gray, 80IRE
**(normal line) Model : For LGD (LB56xx, LB55xx)
▪ Stand a rd colo r c o ordin a te and t emper a ture usi n g
CA-210(CH-14) – by aging time
H/R Time(Min)
Cool Medium Warm
x y x x y x
271 270 286 289 313 329
1 0-2 281 285 296 304 323 344
2 3-5 280 284 295 303 322 343
3 6-9 279 282 294 301 321 341
4 10-19 277 279 292 288 319 338
5 20-35 275 275 290 294 317 334
6 36-49 273 273 288 292 315 332
7 50-79 272 272 287 291 314 331
8 80-119 271 270 286 289 313 329
9 Over 120 271 270 286 289 313 329
**(aging chamber) Model : For LGD (LB56xx, LB55xx)
▪ Sta nda rd col or coo rdinate and temperatur e usi ng
CA-210(CH-14) – by aging time
H/R Time(Min)
Cool Medium Warm
x y x x y x
271 270 286 289 313 329
1 0-5 280 285 295 304 319 340
2 6-10 276 280 291 299 315 335
3 11-20 272 275 287 294 311 330
4 21-30 269 272 284 291 308 327
5 31-40 267 268 282 287 306 323
6 41-50 266 265 281 284 305 320
7 51-80 265 263 280 282 304 318
8 81-119 264 261 279 280 303 316
9 Over 120 264 260 279 279 303 315
** For INX,AUO,SHARP,CSOT Module.( In the case of , the color
temperature spec of cool mode is 13000K)
H/R Time(Min)
Cool Medium Warm
x y x x y x
spec 271 270 286 289 313 329 329
target 276 277 291 296 318 336 340
5.2. Option selection per country
5.2.1. Overview
(1) Tool option selection is only done for models in Non-USA
North America due to rating
(2) Applied model: LA32B Chassis applied to CANADA and
MEXICO
5.2.2. Country Group selection
(1) Press ADJ key on the Adj. R/C, and then select Country
Group Menu
(2) Depending on destination, select US, then on the lower
Country option, select US, CA, MX.
Selection is done using +, - KEY
(3) Using DFT(Auto)
※ PC (for communication through RS-232C) -> UART Baud
rate : 115200 bps
Command : ah 00 00 DATA(Area Number(hexadecimal))
ITEM DATA(Area Number) AREA
AREA OPTION1 0 USA
1 CANADA
2 MEXICO
5.2.3. Tool Option inspection
▪ Press Adj. key on the Adj. R/C, then select Tool option
Model Module
Tool
option1
Tool
option2
Tool
option3
Tool
option4
32LB550B-UZ LGD 784 13314 41036 20544
32LB560B-UZ SHARP 13074 9218 41036 20544
32LB550B-UZ SHARP 13074 13314 41036 20544
42LB5500-UZ LGD 1552 5126 41036 24640
42LB5500-UZ AUO 9744 5126 41036 24640
42LB5600-UZ LGD 1552 1030 41036 24640
42LB5600-UZ AUO 9744 1030 41036 24640
39LB5600-UZ INX 17682 1030 41036 24640
49LB5500-UZ LGD 2064 5126 41036 24640
55LB5500-UZ LGD 2576 5126 41036 24640
55LB5500-UZ BOE 23058 5126 41036 24640
32LB550B-UZ BOE 21266 13314 41036 24640
32LB5600-UZ LGD 784 1026 41036 24640
32LB560B-UZ LGD 784 9218 41036 20544
※ Tool option can be reconstructed by Software
5.3. Ship-out mode check (In-stop)
- After final inspection, press In-Stop key of the Adj. R/C and
check that the unit goes to Stand-by mode