LG 55EJ5E - Page 110

ENGLISH
72
67. Brightness Scheduling (Command: s s)
Sets Brightness Scheduling.
Transmission
[s][s][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data 1
1. f1 to f6 (data reading)
F1: Reads the 1st brightness schedule's data
F2: Reads the 2nd brightness schedule's data.
F3: Reads the 3rd brightness schedule's data.
F4: Reads the 4th brightness schedule's data.
F5: Reads the 5th brightness schedule's data.
F6: Reads the 6th brightness schedule's data.
FF: Reads all stored lists
3. e1 to e6 (Deletes one index), e0 (Deletes all indexes)
E0: Deletes all brightness schedules.
E1: Deletes the 1st brightness schedule.
E2: Deletes the 2nd brightness schedule.
E3: Deletes the 3rd brightness schedule.
E4: Deletes the 4th brightness schedule.
E5: Deletes the 5th brightness schedule.
E6: Deletes the 6th brightness schedule.
4. 00 to 17: Hour 00 to hour 23
Data 2 00 to 3B: Minute 00 to minute 59th
Data 2 00 to 64: Backlights 0 to 100
* To read or delete a brightness schedule you have set, [Data2]
[Data3] must be set to FF.
* If you want to read all configured brightness schedules
through FF, do not enter any values in [Data2][Data3].
* When all configured brightness schedules are read through
FF, OK is acknowledged even if there is no stored list.
Example 1: fd 01 f1 ff ff - Reads the 1st index data in
Brightness Scheduling.
ex2: sn 01 1b ff ff ff ff – Reads all index data in in Brightness
Scheduling.
Example 3: fd 01 e1 ff ff - Deletes the 1st index data in
Brightness Scheduling.
Example 4: ss 01 07 1E 46 - Adds a schedule whose time is
07:30 and whose backlight is 70.
* This feature may not be supported on some models.
Acknowledgment
[s][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
68. Multi Screen Mode & Input (Command: x c)
Saves and controls Multi Screen modes and inputs.
Transmission
[x][c][ ][Set ID][ ][Data1][ ][Data2][ ][Data3[ ][Data4]
[ ][Data5][ ][Cr]
Data 1 (Sets MultiScreen mode)
10: PIP
22: PBP2
23: PBP3
24: PBP4
Data 2 (Sets the MultiScreen Main Input)
Data 3 (sets the MultiScreen Sub1 Input)
Data 4 (sets the MultiScreen Sub2 Input)
Data 5 (sets the MultiScreen Sub3 Input)
80: DVI-D
90: HDMI1
91: HDMI2/OPS
92: OPS/HDMI3/DVI-D
95: OPS/DVI-D
96: HDMI3/DVI-D
97: HDMI3/HDMI2/DVI-D
98: OPS
C0: DISPLAYPORT
Acknowledgment
[c][ ][Set ID][ ][OK/NG][ ][Data1][Data2][Data3]
[Data4][Data5][x]
* This feature may not be supported on some models.
* Only the input modes supported by the model works.
* This feature operates as the last input, and supports data in
DTV format.
69. Aspect Ratio (Multi Screen) (Command: x d)
Saves and controls aspect ratios (Multi Screen).
Transmission
[x][d][ ][Set ID][ ][Data1][ ][Data2][Cr]
Data 1 Controls the Main input
02: Controls the Sub1 input
03: Controls the Sub2 input
04: Controls the Sub3 input
Data 2 00: Full
01: Original
Acknowledgment
[d][ ][Set ID][ ][OK/NG][Data1][Data2][x]
* This feature may not be supported on some models.