37
206-4322
Installer Menu (Cont.)
070 - FOR. CH-TIME (Display Characters Foreground Color)
Set the foreground color for MPI display characters according to
the following color chart:
0 = Black 2 = Green 4 = Red 6 = Yellow
1 = Blue 3 = Cyan 5 = Violet 7 = White
If the foreground and background colors for the display characters
are the same, the background will be transparent.
Note: This item and item 071 BCK. CH-TIME also apply to the
“Channel Not Available” message if item 073 CH NOT AVBLE is
set to 1 (enabled).
Note: Items 070 FOR. CH-TIME and 071 BCK. CH-TIME are only
available in the Installer Menu when item 069 EN. CH-T COL. is
set to 1.
071 - BCK. CH-TIME (Display Characters Background Color)
See description for item 070 FOR. CH-TIME above. The color
chart is the same for both items.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL
NOT AVAILABLE” message is displayed when a user attempts to
direct tune a channel that is not included in the channel lineup.
Note: This item is not available in the Installer Menu when item
028 CH. OVERIDE is set to 1.
Note: This item is only applicable when the TV is in PTC-CTV
Mode.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, the TV auto-
matically tunes to the specied Start Channel.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 255.
078 - UPN MSB (UPN Most Signicant Byte)
User programmable number, most signicant byte readable by
MPI command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Signicant Byte-1)
User programmable number, most signicant byte-1 readable by
MPI command. Note: Not linked to serial number.
080 - UPN MSB-2 (UPN Most Signicant Byte-2)
User programmable number, most signicant byte-2 readable by
MPI command. Note: Not linked to serial number.
081 - UPN LSB (UPN Least Signicant Byte)
User programmable number, least signicant byte readable by
MPI command. Note: Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing MPI timing requirements to be compatible with PC-
based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
084 - PERMANENT BLK (Permanent Block)
Allows Parental Control blocking schemes to be permanent by
disabling the user’s ability to limit blocking hours in the Function
Menu. Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specied hours control of blocking schemes. See
also item 022 MAX BLK HRS.
Note: This item is not available in the Installer Menu when item
021 V-CHIP is set to 0.
086 - V. MUTE TIME (Video Mute Time)
Use to extend the normal video mute time during channel change.
For example, you may wish to extend the normal video mute time
to prevent the display of encrypted video (i.e., from a Pro:Idiom
encrypted channel) that has not yet been decrypted. When set to
0, the normal video mute time is not extended. Set from 1 to 50 to
increase the normal video mute time in 100 ms step increments up
to a maximum of 5 seconds (e.g., the value of 25 represents 2.5
seconds, or 25 x 100 ms = 2.5 seconds).
088 - EN NOISE MUTE (Enable Noise Mute)
Applicable for analog channels only. If set to 1, audio mutes if no
signal is present.
090 - KEY LOCK
If set to 1, Key Lock is enabled, which means that all display
panel joystick button functions will be locked, i.e., non-functional.
Set to 0 to disable Key Lock. Note that all IR features remain
functional regardless of this setting.
091 - HDMI2 ENABLE
Set to 1 to enable HDMI 2 input in DTV Mode. Set to 2 to enable
HDMI 2 input in PC Mode. Set to 0 to disable display panel HDMI
2 input.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable the SAP feature in the Function Menu (i.e.,
the TV is not in Pass-through Mode). Set to 0 to disable the SAP
feature in the Function Menu.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects the aspect ratio to be set as default each time the TV is
turned ON:
0 = Set By Program 1 = 4:3
2 = 16:9 (default) 3 = Just Scan
4 = Zoom
Note: See also item 106 ASP RATIO LOCK. This item (i.e., item
096) is not available in the Installer Menu when item 106 is set to 1.
To Next Page
Loading...
