To Next PageTo Next PageWhy is my LG GCW1069CS Washer showing a drain error?
The LG Washer may display a drain error because it has not fully drained within 3 minutes. To resolve this, examine the drainage system for any obstructions.
What to do if my LG GCW1069CS displays an imbalance error?
If your LG Washer shows an imbalance error, it could be due to several reasons: the load is too small, the appliance is tilted, laundry is gathered to one side, or non-distributable items are in the drum. The suggested solution is to redistribute the load evenly inside the drum.
How to fix a water inlet error on my LG Washer?
A water inlet error on your LG Washer occurs when the correct water level is not reached within 10 minutes after water is supplied, or if it doesn't reach the preset level within 12 minutes. Check if water is being supplied properly to resolve this issue.
What to do if my LG Washer has a door open error?
If your LG Washer displays a door open error, it could be due to the door not being fully closed, loose electrical connections at the door switch and PWB Assembly, or a faulty DOOR SWITCH ASSEMBLY. Make sure the door is fully closed and check the electrical connections.
How to troubleshoot a locked motor error on an LG GCW1069CS Washer?
A locked motor error on your LG Washer can be caused by several issues: * The MOTOR HARNESS connector is disconnected from the STATOR ASSEMBLY connector. * Poor electrical contact between the MOTOR HARNESS connectors and the MAIN PWB ASSEMBLY connector. * A cut in the MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY. * A defective hall sensor. Check the connections and integrity of the MOTOR HARNESS to troubleshoot this error.
What causes an overflow error on my LG Washer?
An overflow error on your LG Washer indicates that the water level frequency is too high. Check for issues causing water overflow. If the error is displayed, the drain pump will automatically activate to drain the water.
What does a pressure sensor error mean on my LG Washer?
A pressure sensor error on your LG Washer indicates that the SENSOR SWITCH ASSEMBLY is out of order. You should inspect and replace the SENSOR SWITCH ASSEMBLY if necessary.
What does EEPROM error mean on LG GCW1069CS Washer?
An EEPROM error on your LG Washer indicates that the EEPROM is out of order. Replace the EEPROM to resolve this issue.
What to do if my LG Washer shows a card reader error?
A card reader error on your LG Washer means that there is a disconnection of the Card Reader Wire. Reconnect the Card Reader Wire.
Direct drive motor, tilted drum, large door for easier use.
Ultra capacity drum and see-through door for enhanced functionality.
Magnetic door plunger for drying and tub clean for hygiene.
General precautions to reduce risk of fire, shock, or injury.
Importance and procedure for proper grounding.
Safety guidelines specific to washer installation.
Safety guidelines for operation, maintenance, and disposal.
Illustrates and labels major components of the washer.
Lists and illustrates accessories provided with the washer.
Explains the control panel for coin-operated models.
Explains the control panel for card-operated models.
Explains the control panel for OPL (On-Premise Laundry) models.
Guidance on selecting a site and removing shipping bolts.
Steps for connecting water supply and drain lines.
How to level the washer and use optional pads for stability.
Precautions for fabric care and guidelines for sorting laundry.
Recommendations for detergents, softeners, and dispenser operation.
Correct procedures for loading detergent, bleach, and softener.
Describes ready mode, inserting payment.
How to select cycles, add features, and understand cycle finish.
Methods to access and navigate programming menus.
Configuring prices, schedules, features, and payment types.
Steps to enter diagnostic test mode and perform factory reset.
Steps to access and understand collected usage data.
Post-wash, dispenser, and door seal cleaning.
Cleaning water inlet filters, drain pump filter, and drum.
Explains error codes, causes, and solutions.
Machine behavior during power outages and technical details.
General
