GX500 Operational Description Revision A
LG Electronics 130/143 LGE Property
VIII. ENGINEERING MODE
Engineering mode is designed to allow a service man/engineer to view and test the basic functions
provided by a handset. The key sequence for switching the engineering mode on is “1809#*500# “.
Pressing END will switch back to non-engineering mode operation. Drag a screen to select a menu
and press ‘OK’ to progress the test. Pressing ‘BACK’ will switch back to the original test menu.
Engineering mode(Test Mode) can be divided by ‘Factory Mode’ and ‘Eng Mode’
[2-6] WLAN Service
[2-6-1] Net Info
[2-6-2] Rx Tx Test
[2-6-3] Open
[2-6-4] IP Configuration
[2-6-5] Available Net
[2-6-6] OTA Mode ON
[2-6-7] OTA Mode OFF
[2-6-8] Iperf Test
[2-6-9] Close
[2-6-10] Disconnect
[2-7] Defect Report System
[3] Band Select
[4] Band Select Remote
[5] Network Info
[6] Others
[6-1] Bluetooth test Mode
[6-2]Aging Test
[6-3] Touch Screen Test
[6-4] FM Radio Test
[6-5] Debug Test
[6-6] Keytone Aging
[6-7] Touch Calibration
[6-8] Common Test
[6-9] Trace Option
[6-10] FPRI Test
[6-11] Bypass Booting Mode
[6-12] FXUI Debug Setting
- Factory Mode
[1] Device Test
[1-1] Function Test
[1-2] Main LCD
[1-3] LCD Backlight
[1-4] Key Backlight
[1-5] Speaker
[1-6] Vibrator
[1-7] Camera
[1-8] MicRcv
[1-9] Keypad
[1-10] Motion Sensor Test
[2] ELT Mode
[2-1] AutoMatic
[2-2] Manual
[2-2-1] LCD Backlight
[2-2-2] Ringtones
[2-2-3] Vibrator
[2-2-4] Camera
[2-2-5] Auto Loopback
[2-2-6] Ring & Vibrator
[3] SW Sanity Test
[3-1] E Serial NO
[3-2] UA.Strung
[3-2-1] Browser Setting
[3-2-2] Push Dump
[3-2-3] Send Message
[3-2-1] Savepage Dump
[3-3] Unlock SIM
[4] Version
[5] Factoru Reset
[1] Usage Info
[1-1] Call Timer
[1-2] User Tendency
[1-3] Usage Tracking
[2] Eng Mode
[2-1] Device Info
[2-1-1] Battery info
[2-1-2] LCD Info
[2-1-3] Firmware Info
[2-2] Audio Tunning
[2-2-1] Handset
[2-2-2] Headset
[2-2-3] Speaker Phone
[2-2-4] Bluetooth Headset
[2-2-5] Tunning Info
[2-2-6] Default
[2-2-7] Save to File
[2-3] Audio Tunning Remote
[2-3-1] Handset
[2-3-2] Headset
[2-3-3] Speaker Phone
[2-3-4] Bluetooth Headset
[2-3-5] Tunning Info
[2-3-6] Default
[2-3-7] Save to File
[2-4] UART Setting
[2-4-1] Auto
[2-4-2] AT CMD
[2-4-3] UART Info
[2-5] BT Testing
[2-5-1] Audio Test
[2-5-2] RF Test
- Eng Mode
To Next Page
Loading...
