To Next PageTo Next PageWhy does my LG Washer show an imbalance error?
An imbalance error on your LG Washer can occur for several reasons: the load is too small, the appliance isn't level, laundry is bunched to one side, or non-distributable items are in the drum. Check these potential causes to resolve the issue.
What causes a drain error on an LG WD-14120FD Washer?
A drain error on your LG washer means that water hasn't drained sufficiently within 10 minutes. Check the drain hose for any clogs or kinks that may be preventing proper drainage.
What causes a lock error on my LG WD-14120FD Washer?
A lock error on your LG Washer can stem from several connection issues or a defective hall sensor. Here are potential causes and solutions: 1. The LEAD WIRE ASSEMBLY connector isn't connected to the STATOR ASSEMBLY connector: Reconnect or repair the connector. 2. Poor electrical contact between connectors in the LEAD WIRE ASSEMBLY and MAIN PWB ASSEMBLY: Reconnect or repair the contact in the connector. 3. The LEAD WIRE ASSEMBLY is cut: Repair the damaged LEAD WIRE ASSEMBLY. 4. The hall sensor is defective: Replace the STATOR ASSEMBLY.
What to do if my LG WD-14120FD shows a door open error?
A 'door open error' on your LG washer indicates that the Start/Pause button was pressed while the door was open or that the door switch is malfunctioning. Ensure the door is properly closed before starting the cycle. If the issue persists, the door switch may be faulty.
Why is my LG WD-14120FD Washer showing an overflow error?
An overflow error on your LG washer occurs when too much water enters the tub, triggering an automatic pump-out. This indicates an issue with the water level control.
What does a current error mean on my LG WD-14120FD?
A current error on your LG Washer can be due to two reasons. It could be a faulty MAIN PWB ASSEMBLY, in which case you should replace it. Alternatively, the winding in the STATOR ASSEMBLY might be short-circuited, requiring replacement of the STATOR ASSEMBLY.
What does a heating error mean on my LG WD-14120FD?
A heating error on your LG washer indicates that the THERMISTOR is out of order. This component is responsible for monitoring and regulating the water temperature during the wash cycle.
What does sensor pressure S/W error mean on LG Washer?
A 'sensor pressure S/W error' on your LG washer indicates that the sensor pressure switch is malfunctioning. This switch is responsible for monitoring the water pressure inside the washer.
General| Type | Front Load |
|---|---|
| Capacity | 8 kg |
| Spin Speed | 1400 RPM |
| Energy Rating | A+++ |
| Color | White |
| Inverter Motor | Yes |
| Steam Function | Yes |
| Noise Level (Wash) | 54 dB |
| Noise Level (Spin) | 74 dB |
| Programs | 14 |
| Display | LED |
| Child Lock | Yes |
| Delay Start | Yes |
Describes key features like jumbo drum, intelligent wash system, direct drive, child-lock, low noise, and auto restart.
Explains how fuzzy logic determines washing time based on sensor inputs.
Details the water level control mechanism using a pressure sensor.
States that the door cannot be opened while the program is operating.
Lists and illustrates included accessories like inlet hose and wrench.
Outlines the standard installation steps including removing transit bolts and leveling.
Instructions on connecting the water inlet hose properly to prevent leaks.
Guidelines for connecting the drain hose correctly, avoiding submersion and twists.
Instructions for safely connecting the power plug, avoiding multi-device connections.
Explains how to set, cancel, and the functionality of the child lock feature.
Describes how to set a delay for the wash cycle, including maximum hours.
Details the function of the Start/Pause button for starting, pausing, and auto-power off.
Explains how to select wash programs using the dial.
Describes the option to reduce wash program time, noting its unavailability with Quick 30.
Explains what the LED display shows, including remaining time and error indications.
Explains the function of the ON/OFF button to turn the appliance on and off.
Guides on using buttons for manual wash, rinse, and spin selections.
Details how to select water temperature options for different programs.
Safety precautions to take before starting troubleshooting procedures.
Instructions for entering and operating the QC test mode for diagnostics.
Method to check water level frequency by pressing specific buttons.
Lists and explains various error codes, their symptoms, and causes.
Provides a flowchart for diagnosing and resolving abnormal operation symptoms.
Step-by-step guide for disassembling the control panel assembly.
Instructions for disassembling the detergent dispenser assembly.
Details on disconnecting and removing the inlet valve assembly.
Steps to remove the main printed circuit board (PWB) assembly.
Instructions for removing the lower cover of the appliance.
Procedure for removing the door assembly, including hinge screws.
Steps for removing and reassembling the door gasket and related clamps.
Instructions for disassembling rotor, stator, and friction damper assemblies.
Guide on how to safely clean the drain pump filter.
Steps for removing the drain pump assembly, including hoses and wiring.
Procedure for loosening and removing the heater assembly.
Instructions for removing and remounting the thermistor.
Steps to disassemble the door lock switch assembly and disconnect wiring.
Procedure to remove foreign material stuck between the drum and tub.
Exploded view and part list for the cabinet assembly.
Exploded view and part list for the control panel and dispenser assembly.
Exploded view and part list for the drum and tub assembly.
