LG WM22WV26SR User Manual (English)

Questions and Answers:

A
Alexis VelasquezSep 6, 2025
How to fix 1E inlet error on my LG Washer?
- T
  Trevor MaxwellSep 6, 2025
  If the LG Washer displays a '1E INLET ERROR', it means the water supply isn't adequate. First, check another tap in the house to ensure general water supply. Then, fully open the water supply tap connected to the washer. Inspect the water supply hoses for any kinks and straighten them or reinstall them. Finally, turn off the taps, disconnect the hoses from the washing machine, and check and clean the inlet valve filter, as it may be clogged.
S
Stephen YoungSep 5, 2025
What does LE MOTOR LOCKED ERROR mean on LG WM22WV26SR?
- J
  Joseph GreenSep 5, 2025
  The LE MOTOR LOCKED ERROR on your LG Washer indicates an overload in motor. Let the appliance wait for 30 minutes until the motor is cooled down and then, restart the cycle.
A
Amanda CarterSep 4, 2025
What does PF POWER FAILURE mean on my LG WM22WV26SR Washer?
- A
  Aaron AndersonSep 4, 2025
  The PF POWER FAILURE on your LG Washer indicates that a power failure or inadequate electrical service may have occurred during operation. Press the Start/Pause button to restart the cycle.
T
Tina KingAug 23, 2025
Why does my LG WM22WV26SR Washer show UE unbalance error and how to fix it?
- A
  austinkathrynAug 25, 2025
  If your LG Washer displays a 'UE UNBALANCE ERROR', it indicates an imbalance in the load. If clothes are too wet, rearrange the load for proper spinning, close the door, and press Start/Pause. For loads that are too small, add one or two similar items to balance it. Close the door and press Start/Pause again. The door must be locked before spin can be achieved.
Z
Zachary PhelpsSep 2, 2025
What does OE WATER OUTLET ERROR mean on my LG WM22WV26SR and how can I fix it?
- M
  melissa37Sep 2, 2025
  The OE WATER OUTLET ERROR on your LG Washer indicates that the drain hose is kinked or clogged, so clean and straighten the drain hose. Alternatively, the drain filter may be clogged, so check and clean the drain filter.
G
Gina CoffeySep 1, 2025
How to resolve 1E INLET ERROR on LG Washer?
- D
  Daniel MayoSep 2, 2025
  The 1E INLET ERROR on your LG Washer indicates that the water supply is not adequate in that location, so check another tap in the house. Also, ensure the water supply tap is completely open. Straighten any kinked water supply hoses or reinstall the water inlet hose. Check and clean the inlet valve filter after turning off the taps and removing the hose connections to the washing machine.
B
Brittany GarciaSep 1, 2025
How to fix UE UNBALANCE ERROR on LG Washer?
- S
  Sandra PetersonSep 1, 2025
  The UE UNBALANCE ERROR on your LG Washer indicates that the clothes may be too wet at the end of the cycle, so rearrange the load to allow proper spinning, then close the door and press the Start/Pause button. This error can also appear if the load is too small, so add 1 or 2 similar items or smaller articles of clothes to help balance the load, then close the door and press the Start/Pause button.
E
Edward OliverAug 31, 2025
Why is detergent not dispensed in my LG WM22WV26SR Washer?
- J
  Joanne PerezAug 31, 2025
  If detergent is not dispensed incompletely or at all in your LG Washer, it could be because too much detergent is used, so follow the guidelines provided by the detergent manufacturer. Also, the Drain Pump Filter may be blocked, so clean the Drain filter.
A
ashleyblakeAug 30, 2025
Why is my LG WM22WV26SR Washer not draining water?
- M
  Mary SmithAug 30, 2025
  If your LG Washer isn't draining water, check if the drain hose is kinked and ensure that the drain hose is not kinked. Also, ensure the drain is not located higher than 1 m above the floor, so make sure that the drain hose is no higher than 1 m above the bottom of the appliance.
H
Henry BrownAug 29, 2025
What to do if my LG WM22WV26SR Washer does not operate?
- H
  Holly HardinAug 29, 2025
  If your LG Washer isn't operating, check these things: The control panel may have powered off due to inactivity, so press the Power button to turn the appliance on. Ensure the appliance is plugged securely into a working outlet. Verify the water supply is turned on completely. Also, make sure the programme is correctly set, close the door, and press the Start/Pause button.