Life Fitness X 15 Assembly Instructions

Tools required: Metric Socket set, Phillips Screwdriver, Metric Wrench set
1.
2.
3.
4.
Position the base unit near the desired location for use (Refer to the "Getting Started" section of the User Manual for proper location). Locate and install the four
LEVELER FEET (A) into the front and rear stabilizers as shown.
With the DISPLAY CONSOLE MOUNTING PLATE (B) facing upward, lay the UPRIGHT TUBEASSEMBLY (C) on floor in front of BASE FRAME (D). Cut the wire
tie securing the LOWER WIRE HARNESS (E) to the front of the BASE FRAME. Connect the UPPER WIRE HARNESS (F) to the LOWER WIRE HARNESS.
Position the UPRIGHT TUBE ASSEMBLY (C) between the plates on the front of the BASE FRAME (D). Feed any excess wire harness into the BASE FRAME. Tilt
the UPRIGHT TUBE ASSEMBLY into an upright position. Align the holes on the plates with the holes on the UPRIGHT TUBEASSEMBLY. Secure the UPRIGHT
TUBE ASSEMBLY to the BASE FRAME using four 67 mm HEX HEAD BOLTS (1), eight CAP WASHERS (2) (4 on each side) and four NUTS (3). Leave BOLTS
loose at this time.
Using two 30 mm HEX HEAD BOLTS (4), secure the UPRIGHT TUBE ASSEMBLY (C) to the backside of the SUPPORT PLATE on the BASE FRAME (D). Tighten
the BOLTS securely. Tighten the previous four HEX HEAD BOLTS (1) securely. Install eight black PLASTIC COVER CAPS (5) over each 67 mm HEX HEAD BOLT
HEAD (1) and NUT (3).
Slide the tab of the UPRIGHT TUBE ANGLE BRACE (G) into the slot located near the base of the UPRIGHT TUBE ASSEMBLY (C) and pivot the UPRIGHT TUBE
ANGLE BRACE downward to met the BASE FRAME (D). Using two 12 mm SCREWS (6), secure the UPRIGHT TUBE ANGLE BRACE to the UPRIGHT TUBE
ASSEMBLY and BASE FRAME as shown.
Slide one LARGE FLAT WASHER (7) and one LARGE WAVE WASHER (8) onto the USER RIGHT PIVOT SHAFT (H). Slide the WASHERS fully over the PIVOT
SHAFT until seated against the pre-installed stop ring.
Locate the USER RIGHT ROCKER ARM ASSEMBLY (J) (Marked with an “R”). With the top handgrip facing the front of the unit (as shown), slide the USER RIGHT
ROCKER ARMASSEMBLY onto the USER RIGHT PIVOT SHAFT (H) until seated against the WASHERS (7 & 8). Secure the ROCKER ARMASSEMBLY to the
PIVOT SHAFT using one FLAT WASHER (9), LOCK WASHER (10), and 20 mm HEX HEAD BOLT (11). Tighten the BOLT securely. Insert one ROCKER ARM
END CAP (K) into the end of the ROCKER ARM SHAFT. Repeat the procedure for the USER LEFT ROCKER ARM ASSEMBLY (L).
Locate the USER RIGHT PEDAL LEVER (M) and PEDAL (N) (marked with an “R”). Position the PEDAL above the PEDAL MOUNTING PLATE (O) and secure the
PEDAL using four 16 mm SCREWS (12) and LOCK WASHERS (13). Tighten the SCREWS securely. Repeat for the USER LEFT PEDAL (P) and PEDAL LEVER
(Q).
Position the rear end of the USER RIGHT PEDAL LEVER (M) near the USER RIGHT REAR CLEVIS (R). Position the end of the PEDAL LEVER between the
clevis flanges. Align the holes and secure as shown using two CLEVIS COVERS (S), two CAP WASHERS (2), one 90 mm HEX HEAD BOLT (14), one NUT (3)
and two PLASTIC COVER CAPS (5). Tighten the BOLT and NUT securely.
5.
6.
X1 Cross-Trainer5
Hardware List
1.&2.&3.
7.
8.&9.
Assembly Sequence
Pedal Arms
Levelers & Monocolumn
5.&6.
Pedals & Right Rear
Pedal Lever
Pedal Lever &
Rocker Arm Assembly
Console & Water Bottle
10 706020 8030 9040 100 12050 110 130 140 150 160
4.
Item Qty Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
14
7
2
14
2
2
2
2
2
2
8
8
1
2
6
67 mm Hex Head Bolt
Cap Washer
30 mm Hex Head Bolt
Plastic Cover Caps
12 mm Phillips Screw
Large Flat Washer
Large Wave Washer
Flat Washer
Washer
0 mm Hex Head Bol
Phillips Screw
Lock Washer
90 mm Hex Head Bolt
mm Hex Head Bolt
12 mm Phillips Screw
Hex Head Nut
Lock
2t
16 mm
81.5
7.
8.
9.
10.
Lift the front end of the USER RIGHT PEDAL LEVER (M) to meet the USER RIGHT ROCKER ARM CLEVIS (T). Secure the PEDAL LEVER to the ROCKERARM
CLEVIS using two CAP WASHERS (2), one 81.5 mm HEX HEAD BOLT (15), one NUT (3) and two PLASTIC COVER CAPS (5). Tighten the BOLT and NUT
securely. Repeat the procedure for the USER LEFT PEDAL LEVER (Q) and ROCKERARM CLEVIS (U).
Position the DISPLAY CONSOLE (V) over the DISPLAY CONSOLE MOUNTING PLATE (B) located at the top of the UPRIGHT TUBE ASSEMBLY (C). Plug the
CONNECTOR (W) leading from the DISPLAY CONSOLE MOUNTING PLATE into the corresponding CONNECTOR in the back of the DISPLAY CONSOLE. Make
sure the CONNECTOR snaps into place. Push excess wire harness into the opening of the DISPLAY CONSOLE MOUNTING PLATE.
Secure the DISPLAY CONSOLE (V) to the DISPLAY CONSOLE MOUNTING PLATE (B) using four 12 mm SCREWS (16). Tighten the SCREWS securely.
CAUTION: Be careful not to pinch the wire harness when assembling the DISPLAY CONSOLE (V) to the DISPLAY CONSOLE MOUNTING PLATE (B).
Secure the WATER BOTTLE BRACKET (X) to the UPRIGHT TUBE ASSEMBLY (C) as shown using two 12 mm SCREWS (16). Tighten the SCREWS securely.
Insert the WATER BOTTLE (Y) into the WATER BOTTLE BRACKET.
Refer to the "Getting Started" section of the User Manual for proper location, stabilizing, and POWER ADAPTER instructions.
Assembly Guide:
Look for the number coded
hardware bags that match the
assembly sequence.
1) 2)
4)
6) 3)5)
11) 10) 9)
7) 8)
12)
14)
13) 3)
15) 3)
16)
5
14
13
12
O
N
5
2
3
2
15
5
Q
S
P
2
3
5
S
2
R
5
A
1
2
D
E
C
F
6
G
2
3
5
4
B
U
7
8
J
9
11
10
K
H
C
16
B
W
Y
X
16
C
M
T
U

Life Fitness X 15 Specifications

General

Brand	Life Fitness
Model	X 15
Category	Elliptical Trainer
Language	English