To Next PageTo Next PageWhy is it difficult to see through my Lincoln Electric Welding Accessories filter?
It might be difficult to see through the filter of your Lincoln Electric Welding Accessories due to a dirty front cover lens. Try cleaning or replacing the front cover lens. Another cause could be a dirty cartridge. Clean the auto-darkening cartridge with a soapy water solution and a soft cloth.
What to do if my Lincoln Electric Welding Accessories filter does not darken when arc is struck?
If the filter on your Lincoln Electric Welding Accessories isn't darkening when an arc is struck, it could be due to several reasons. First, the sensitivity might be set too low; try adjusting it to the required level. Also, a dirty or damaged front cover lens can be the cause, so clean or replace it as needed. Ensure that you are not blocking the sensors or solar panels while welding and that the proper shade is selected, since Grind Mode might be active.
Why does my Lincoln Electric VIKING 3350 filter remain dark after welding?
If your Lincoln Electric Welding Accessories filter stays dark after you finish welding, the delay time might be set too high. Try adjusting the delay time to the level you need.
Why is my Lincoln Electric VIKING 3350 filter darkening without an arc?
If your Lincoln Electric Welding Accessories filter is darkening even when there's no arc, the sensitivity might be set too high. Adjust the sensitivity to the required level.
How to improve visibility through my Lincoln Electric VIKING 3350 filter?
If it's difficult to see through the filter, it could be due to: * A dirty front cover lens. Clean or replace it. * A dirty cartridge. Clean the auto-darkening cartridge with a soapy water solution and a soft cloth.
What to do if my Lincoln Electric Welding Accessories filter remains dark after welding?
If the filter remains dark after completing a weld, the delay time might be set too high. Adjust the delay time to the required level.
How to fix a Lincoln Electric Welding Accessories filter that doesn't darken when the TEST button is pushed?
If the filter does not darken when the TEST button is pushed, the battery might be low. Replace the battery.
Why won't my Lincoln Electric VIKING 3350 helmet switch to grind mode?
If the helmet will not switch to grind mode after pressing the button: * Ensure the button is held for 3 seconds. * Check that the plug-in jack from the filter is completely inserted into the button port. Remove and re-insert it.
What should I do if the ADF of my Lincoln Electric VIKING 3350 Welding Accessories is cracked and weld spatter is damaging the filter?
If the ADF is cracked and weld spatter is damaging the filter: * Stop using the product immediately, as UV/IR protection may be compromised, potentially causing burns to the eyes and skin. * Replace the front cover lens if it is missing, damaged, broken, cracked, or distorted.
Why does the Lincoln Electric Motorcycle Accessories filter not darken when an arc is struck?
Several factors can prevent the filter from darkening. The sensitivity might be set too low, so adjust it to the required level. The front cover lens could be dirty, damaged or cracked and needs cleaning or replacing. Obstructions blocking the sensors or solar panel can also cause this, so ensure they are clear. Finally, check that the Grind Mode is not selected by verifying the sensitivity knob setting.
General| Optical Clarity | 1/1/1/1 |
|---|---|
| Shade Range | 5-13 |
| Light State | 3 |
| Switching Speed | 1/25, 000 sec |
| Number of Arc Sensors | 4 |
| TIG Amp Rating | 2 Amps |
| UV Protection | Yes |
| IR Protection | Yes |
| Weight | 21 oz |
| Operating Temperature | 14°F to 131°F (-10°C to 55°C) |
| Storage Temperature | -4°F to 158°F (-20°C to 70°C) |
| Standards | ANSI Z87.1, CSA |
| Power Source | Solar Cells with Replaceable Batteries |
| Material | Polycarbonate |
| Lens Shade | Variable |
Details on protecting eyes and skin from harmful arc rays during welding operations.
Information on the health risks associated with welding fumes and gases, and ventilation requirements.
Guidance on adjusting headgear tightness, crown, tilt, and fore/aft positions for optimal fit.
Instructions for adjusting shade levels using the shade range switch and dual scale dial.
How to use the test button to preview shade selection and its return to light state.
Details on adjusting the sensitivity knob for optimal performance in varying light conditions.
Explanation of the delay time knob for controlling the transition from dark to light state.
Information on the ADF cartridge's power source, including battery and solar assist.
