EasyManua.ls Logo

Lincoln Electric WELD-PAK 100 HD User Manual

Lincoln Electric WELD-PAK 100 HD
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
WWEELLDD--PPAAKK 110000 HHDD
IMT780
January, 2010
22801 St. Clair Ave. Cleveland, Ohio 44117-1199 U.S.A.
Tel. (216) 481-8100
WEB SITE: www.lincolnelectric.com
Safety Depends on You
Lincoln arc welding and cutting equipment is designed and
built with safety in mind. However, your overall safety can be
increased by proper installation ... and thoughtful operation
on your part. DO NOT INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT READING THIS MANUAL
AND THE SAFETY PRECAUTIONS CONTAINED
THROUGHOUT. And, most importantly, think before you act
and be careful.
OPERATOR’S MANUAL
MANUAL DE OPERACIÓN
MANUEL DE L’OPÉRATEUR
La Seguridad Depende de Usted
Los equipos de corte y soldadura al arco Lincoln han sido
diseñados y construidos teniendo en cuenta su seguridad.
No obstante, ésta se verá incrementada si la instalación se
realiza correctamente, y si pone atención en el manejo de
los mismos. NO INSTALE, UTILICE O REPARE ESTE
EQUIPO SIN ANTES HABER LEIDO ESTE MANUAL Y LAS
MEDIDAS DE SEGURIDAD QUE CONTIENE. Y, lo más
importante, piense antes de actuar, y tenga mucho cuidado.
La sécurité dépend de vous
Le matériel de soudage et de coupage à l'arc Lincoln est
conçu et construit en tenant compte de la sécurité. Toutefois,
la sécurité en général peut être accrue grâce à une bonne
installation... et à la plus grande prudence de votre part. NE
PAS INSTALLER, UTILISER OU RÉPARER CE MATÉRIEL
SANS AVOIR LU CE MANUEL ET LES MESURES DE
CURITÉ QU'IL CONTIENT. Et, par dessus tout,
réfléchissez avant d'agir et exercez la plus grande prudence.
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Technical Specification . . . . . . . . . . . . . . . . . . . . . .9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
TABLA DE CONTENIDO
Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Especificaciones Técnicas . . . . . . . . . . . . . . . . . . . . .9
Instalación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Accesorios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Localización de averías . . . . . . . . . . . . . . . . . . . . . . .28
Diagramas de cableado . . . . . . . . . . . . . . . . . . . . . . .30
Partes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
TABLE DES MATIÈRES
Sécurité....................................................................2
Introduction ..............................................................8
Fiche technique .......................................................9
Installation ...............................................................10
Fonctionnement .......................................................15
Accessoires..............................................................22
Entretien...................................................................24
Dépannage ..............................................................28
Schéma de câblage.................................................30
Pièces ......................................................................31
Date of Purchase:
Serial Number:
Code Number:
Model:
Where Purchased:
Copyright © Lincoln Global Inc.
CODES: 10965
11058

Questions and Answers:

Lincoln Electric WELD-PAK 100 HD Specifications

General IconGeneral
Input Current20A
Input Voltage120V
Welding ProcessMIG
Wire Feed Speed50 - 500 IPM
Duty Cycle20% @ 90A
Wire Size Range.035 in

Summary

Safety

Electrical Safety and Arc Ray Protection

Covers electric shock, grounding, arc rays, and related protection.

Electric and Magnetic Field Hazards

Information on dangers from EMF fields and precautions for welders.

Fire and Explosion Prevention

Warnings about sparks, flammable materials, and safe handling of containers.

Fumes and Gases Safety

Precautions against inhaling hazardous fumes and gases.

Cylinder Safety

Safe handling procedures for compressed gas cylinders.

Introduction

General Description

Overview of the Weld-Pak 100HD's features, design, and applications.

Technical Specifications

Installation

Component Identification

Locating and identifying all parts included with the Weld-Pak 100HD.

Location and Work Clamp Installation

Proper placement of the welder and attaching the work clamp.

Gun Installation

Steps for connecting the welding gun assembly to the machine.

Power and Gas Connections

Details on connecting input power and optional gas supply.

Operation

Controls and Settings

Explanation of the machine's controls for power, wire speed, and voltage.

Wire Loading and Threading

Procedures for loading wire onto the spool and threading it through the gun.

Welding Process Guidelines

Instructions for making welds, including process settings and wire types.

Maintenance

Routine Maintenance Procedures

Steps for user-level maintenance of the wire feed compartment and fan motor.

Troubleshooting

Wire Feed and Output Issues

Addresses problems with wire feed, weld output, and gas flow when trigger is pulled.

Wiring Diagram

Parts

Related product manuals