Linksys WRE54G - Wireless-G Range Expander Repeater

A Division of Cisco Systems, Inc.
®
Model No.
Quick Installation
Model No.
Wireless
A If you want to use the Auto
Configuration button, place
the Range Expander next to
your wireless router or access
point. Then proceed to step B.
If you want to connect the
Range Expander to a wired
network for setup, flip up the lid
covering the Ethernet network
port on the Range Expander’s
front panel. Connect the
Ethernet network cable to the
Range Expander and your
router. Proceed to step B.
B Connect the appropriate
power plate, and then
connect it to a power outlet,
preferably a surge protector.
A Press the Range Expander’s
Auto configuration button and
hold it down for five seconds.
Then release the button.
The LEDs on the Range
Expander will flash for up to
one minute while it is being
auto-configured. When both of
the LEDs are solidly lit blue, the
Range Expander is properly
configured and ready for use.
B To move the Range Expander,
unplug it from the power outlet.
C Place the Range Expander in
an optimum location. The best
placement is usually at the
edge of your wireless network.
D Fix the direction of the
antenna. Normally, the higher
you place the Range
Expander’s antenna, the better
the performance will be.
Proper positioning of the
antenna can enhance its
receiving sensitivity.
E Connect the power plate to a
power outlet, preferably a
surge protector.
Congratulations! The installation of
the Wireless-G Range Expander is
complete.
GHz
2.4
802.11g
WRE54G
Range Expander
Package Contents
• One Wireless-G Range Expander
• One AC Power Adapter
• One Setup Wizard CD with User Guide
• One Quick Installation
• One Registration Card
Wireless-G
B
IMPORTANT:If you install the
Range Expander into your
network using the Auto
configuration button and decide
that you want to enable wireless
security on your entire network,
use the Web-based Utility to
enable wireless security on the
Range Expander. Refer to the
User Guide on the CD for details.
OR
D
1
Connecting the Range Expander
Before you begin installation of the Range Expander, make sure your
wireless network is operational.
If your existing wireless network has security disabled, follow the instructions
in “Step 1: Connecting the Range Expander” and “Step 2: Using the Auto
Configuration Button.”
If your existing wireless network has security enabled, follow the instructions
in “Step 1: Connecting the Range Expander” and “Step 3: Using the Setup
Wizard.”
2
Using the Auto Configuration Button

Linksys WRE54G - Wireless-G Range Expander Repeater Specifications

General

Frequency Band	2.4 GHz
Wireless Data Rates	Up to 54 Mbps
Security Features	WEP, WPA, WPA2
Antenna Type	Internal
Operating Temperature	32 to 104°F (0 to 40°C)
Operating Humidity	10% to 85% Non-condensing
Storage Humidity	5% to 90% Non-condensing
Wireless Standard	802.11g
Storage Temperature	-4 to 158°F (-20 to 70°C)
LED Indicators	Power, Wireless

Summary

Connecting the Range Expander

Placement Options

Choose between placing next to the router or connecting via Ethernet cable for initial setup.

Power Connection

Connect the power plate to the Range Expander and plug it into a power outlet.

Using the Auto Configuration Button

Initiate Auto Configuration

Press and hold the Auto Configuration button for five seconds until LEDs flash.

Expander Placement and Power

Unplug, move the Range Expander, and connect it to a power outlet.

Antenna Positioning

Fix the antenna direction for better receiving sensitivity, usually higher placement.

Using the Setup Wizard

Setup Wizard Initiation

Insert the Setup Wizard CD, click Setup, and ensure your wireless router is operational.

Network and Security Configuration

Search for your wireless network, select it, and configure security settings like WEP or WPA.

Range Expander Identification and IP Settings

Search for the Range Expander, enter its password, and configure IP address settings.

Finalizing Setup and Placement

Review settings, save changes, unplug, relocate the Range Expander, and position the antenna.