Longevity WeldAll 200P

Questions and Answers

R
Ray MorganAug 18, 2025
How to troubleshoot Longevity WeldAll 200P that will not turn on?
- B
  bdeleonAug 19, 2025
  If your Longevity Welding System won't turn on, first check the power cords and breaker. If the problem persists, it is recommended to contact LONGEVITY support for further assistance.
T
Timothy MunozAug 21, 2025
What to do if O.C. Over Current LED Lights are on in Longevity Welding System?
- E
  Erin RangelAug 21, 2025
  If the Over Current LED lights are on, it means that your Longevity Welding System has reached its duty cycle. To resolve this, leave the machine's power on and allow the fans to cool it down, or you can turn it off completely to cool it down faster. Do not continue welding until the light turns off.
J
Jennifer WilliamsAug 23, 2025
What to do if Longevity Welding System runs but nothing is happening?
- Y
  Yvonne GreenAug 23, 2025
  If your Longevity Welding System is running but not performing any welding, make sure you've selected the correct mode (plasma cutter, TIG, or stick). Also, inspect the torches and ground connection. Ensure you have argon or compressed air supplied for plasma and TIG welding.
A
Amanda WilliamsAug 26, 2025
How to improve poor cut quality on Longevity WeldAll 200P Welding System?
- B
  Brian DiazAug 26, 2025
  To improve the cut quality of your Longevity Welding System, start by checking the air pressure. Ensure that your unit is capable of cutting the material thickness you are working with. Inspect the consumables to ensure they are producing a stable arc. Replace consumables if necessary, and verify that you have the correct PSI at the regulator.
M
Mr. Daniel ShermanAug 28, 2025
What to do if Longevity WeldAll 200P Welding System will not weld?
- X
  xsmithAug 28, 2025
  If your Longevity Welding System isn't welding, verify the ground connection and torch setup. Ensure you're in the correct mode (ARC/TIG). If TIG welding, confirm you have the appropriate tungsten and filler rod.
J
joshuatrevinoAug 30, 2025
Why is the arc inconsistent on my Longevity WeldAll 200P Welding System?
- J
  James SmithAug 30, 2025
  An inconsistent arc in your Longevity Welding System can be due to improper grounding or insufficient air pressure. Check and replace the consumables, and adjust the regulator to the correct PSI to resolve this issue.
K
ksimmonsSep 1, 2025
What to do if pilot arc will not start on Longevity Welding System?
- N
  Nicholas FrankSep 2, 2025
  If the pilot arc won't start on your Longevity Welding System, check the ground connection. Inspect the torch to ensure proper installation of consumables and replace the consumables if needed.
J
James HansonSep 4, 2025
How to reduce heavy underside slag when cutting with Longevity Welding System?
- C
  Christopher CastilloSep 4, 2025
  If you're experiencing heavy underside slag while cutting with your Longevity Welding System, it's likely due to a slow travel speed. Try increasing the travel speed or the amperage on the unit.
V
virginia83Sep 6, 2025
Why are consumables being consumed quickly on Longevity WeldAll 200P?
- M
  Mrs. Natasha PatelSep 6, 2025
  If the consumables (tips) on your Longevity Welding System are being consumed too quickly, it may be due to improper air or gas flow. Increase the PSI on the regulator, check for leaks in the hose, and maintain a distance of 1/8” from the torch tip to the workpiece.
D
Daniel Bradford PhDSep 8, 2025
Why is tungsten melting or being consumed quickly in Longevity WeldAll 200P Welding System?
- D
  Deborah AllenSep 8, 2025
  If the tungsten is melting or being consumed quickly in your Longevity Welding System, it could be due to low argon gas flow. Check the argon gas flow and increase the post flow. Also, ensure you are using the correct tungsten type and size. A small shield cup could also be the cause.