EasyManua.ls Logo

Lortone 33B - User Manual

Default Icon
12 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LORTONE
ROTARY TUMBLER
INSTRUCTIONS AND PARTS LIST
12130 Cyrus Way
Mukilteo, WA 98275
(425) 493-1600
Model
45C
Model
33B
Model
3-1.5B

Questions and Answers

  • A
    Alexander BurtonAug 9, 2025
    Why is my Lortone 33B barrel not turning?
    • N
      Nicholas CabreraAug 9, 2025
      If the Lortone Power Tool barrel isn't turning, is turning slowly, or stops after you place it on the tumbler, here's what to check: * **Power:** Ensure the machine is properly plugged in and the electrical circuit is working. * **Installation:** Make sure the barrel is correctly aligned. * **Weight:** Avoid exceeding the rated capacity of the barrel. * **Belt:** Tighten the belt if it's slipping. If the drive belt is broken, remove the cover and replace it. * **Motor:** If the motor isn’t running or runs intermittently, it may need to be replaced.
  • M
    Ms. Tracy WrightAug 19, 2025
    What to do if Lortone 33B Power Tool barrel leaks?
    • I
      Ian MillerSep 12, 2025
      If your Lortone Power Tool barrel leaks or the lid comes off during operation, consider the following: * **Inner Lid:** Ensure the inner lid and barrel shoulder are clean and properly seated inside the barrel. * **Knurled Nut:** Tighten the knurled nut by hand until it's snug; avoid over-tightening with tools. * **Gas Build-up:** Occasionally open the barrel to vent any gas that may accumulate during tumbling. * **Gasket:** Check for damage to the barrel or boot gasket and replace if necessary.
  • J
    Jose PeckAug 29, 2025
    Why is my Lortone 33B Power Tool leaking?
    • M
      Mary BarnesAug 29, 2025
      If the barrel of your Lortone Power Tool is leaking or the barrel lid comes off during operation, it could be due to several reasons: * The inner lid might not be seated correctly; ensure the inner lid and barrel shoulder are clean and free of contaminants, and that the inner lid is seated on the shoulder inside the barrel. * The knurled nut might be over tightened; tighten it by hand only until snug, without using tools. * Gas might be building up in the barrel; open the barrel occasionally to vent any gas formed during tumbling. * The barrel or boot gasket might be damaged; replace the damaged barrel or boot gasket.

Summary

Setting Up Your Machine

Install The Barrel Guide

Instructions for installing the barrel guide on the 45C unit.

Getting Started

Open the Barrel

Steps to open the tumbler barrel and remove the inner lid.

Add Rocks

Guidance on filling the barrel with rocks for optimal tumbling results.

Add Abrasive and Water

Instructions for adding abrasive grit and water to the barrel.

Close the Barrel

Procedure for properly closing the tumbler barrel after loading.

Tumble and Rinse

Instructions for operating the tumbler and cleaning after tumbling.

Repeat with Finer Abrasives

Guidance on repeating tumbling steps with progressively finer abrasives.

Troubleshooting

Barrel Operation Issues

Addresses problems like barrel not turning, slow operation, or stopping.

Barrel Leaks or Lid Issues

Addresses issues related to barrel leaks or the lid coming off during operation.

Maintenance

Motor Care

Information on the motor's continuous use design and normal operating temperature.

Barrel Cleaning

Instructions for cleaning the exterior of the barrel and handling slick surfaces.

Bearing Lubrication

Guidance on oiling the shaft bearings every 30 days with specific oil types.

Drive Belt Adjustment and Replacement

Procedures for adjusting drive belt tension and replacing a worn drive belt.

Parts List 33 B, 3-1.5 B

Parts List 45 C

Lortone 33B Specifications

General IconGeneral
BrandLortone
Model33B
CategoryPower Tool
LanguageEnglish

Related product manuals