LTH Electronics MXD75 - Page 591

Registers
- 60 -
Modbus RS485 Interface
Operating Guide
Registers
pH / Redox Input Calibration Continued
6744 Get/Set Channel 1 Buffer A point
5*
FLOAT Custom Buffer A Point 5
*(Only available when
Units is set to pH)
0 to 14.00 pH
7124 Channel 2
7504 Channel 3
6746 Get/Set Channel 1 Buffer B point
5*
FLOAT Custom Buffer B Point 5
*(Only available when
Units is set to pH)
0 to 14.00 pH
7126 Channel 2
7506 Channel 3
6748 Get/Set Channel 1 Temperature
point 5*
FLOAT Custom Buffer Point 5
Temperature
*(Only available when
Units is set to pH)
-20.0°C to 150.0°C
7128 Channel 2 -4.0°F to 302.0°F
7508 Channel 3
6750 Get/Set Channel 1 Buffer A point
6*
FLOAT Custom Buffer A Point 6
*(Only available when
Units is set to pH)
0 to 14.00 pH
7130 Channel 2
7510 Channel 3
6752 Get/Set Channel 1 Buffer B point
6*
FLOAT Custom Buffer B Point 6
*(Only available when
Units is set to pH)
0 to 14.00 pH
7132 Channel 2
7512 Channel 3
6754 Get/Set Channel 1 Temperature
point 6*
FLOAT Custom Buffer Point 6
Temperature
*(Only available when
Units is set to pH)
-20.0°C to 150.0°C
7134 Channel 2 -4.0°F to 302.0°F
7514 Channel 3
6756 Get/Set Channel 1 Buffer A point
7*
FLOAT Custom Buffer A Point 7
*(Only available when
Units is set to pH)
0 to 14.00 pH
7136 Channel 2
7516 Channel 3
6758 Get/Set Channel 1 Buffer B point
7*
FLOAT Custom Buffer B Point 7
*(Only available when
Units is set to pH)
0 to 14.00 pH
7138 Channel 2
7518 Channel 3
6760 Get/Set Channel 1 Temperature
point 7*
FLOAT Custom Buffer Point 7
Temperature
*(Only available when
Units is set to pH)
-20.0°C to 150.0°C
7140 Channel 2 -4.0°F to 302.0°F
7520 Channel 3
6762 Get/Set Channel 1 Buffer A point
8*
FLOAT Custom Buffer A Point 8
*(Only available when
Units is set to pH)
0 to 14.00 pH
7142 Channel 2
7522 Channel 3
6764 Get/Set Channel 1 Buffer B point
8*
FLOAT Custom Buffer B Point 8
*(Only available when
Units is set to pH)
0 to 14.00 pH
7144 Channel 2
7524 Channel 3
6766 Get/Set Channel 1 Temperature
point 8*
FLOAT Custom Buffer Point 8
Temperature
*(Only available when
Units is set to pH)
-20.0°C to 150.0°C
7146 Channel 2 -4.0°F to 302.0°F
7526 Channel 3
6768 Get/Set Channel 1 Buffer A point
9*
FLOAT Custom Buffer A Point 9
*(Only available when
Units is set to pH)
0 to 14.00 pH
7148 Channel 2
7528 Channel 3
6770 Get/Set Channel 1 Buffer B point
9*
FLOAT Custom Buffer B Point 9
*(Only available when
Units is set to pH)
0 to 14.00 pH
7150 Channel 2
7530 Channel 3
6772 Get/Set Channel 1 Temperature
point 9*
FLOAT Custom Buffer Point 9
Temperature
*(Only available when
Units is set to pH)
-20.0°C to 150.0°C
7152 Channel 2 -4.0°F to 302.0°F
7532 Channel 3