Need help?Do you have a question about the LTS LTN8716-P8 and is the answer not in the manual?
Guide to setting the initial administrator password for device security.
Steps for initial NVR setup using the configuration wizard.
Steps to activate IP cameras before adding them to the NVR.
Methods for adding IP cameras detected on the network.
Modifying parameters and configuring custom protocols for connected IP cameras.
Configuring cameras connected via the NVR's Power over Ethernet ports.
Configuring cameras connected via the NVR's integrated network switch ports.
Setting up parameters for controlling PTZ cameras.
Adjusting video quality settings like resolution and bitrate.
Setting up scheduled recording times and types.
Setting up recording triggered by motion detection events.
Configuring recording based on external alarm inputs.
Setting up recording for Video Content Analysis events.
Accessing and reviewing recorded video files.
Searching and playing back recordings based on date and time.
Searching recordings based on event types like alarms or motion.
Procedures for exporting recorded video files to backup devices.
Backing up files found via normal video search.
Backing up event-related video files.
Configuring motion detection sensitivity and response actions.
Configuring handling for external sensor alarms.
Setting up alarms and responses for video signal loss.
Configuring alarms for lens tampering detection.
Defining actions like full-screen monitoring or email alerts for alarms.
Configuring alarms and actions for detecting human faces.
Setting up alarms for objects crossing a defined virtual line.
Configuring alarms for unauthorized entry into defined regions.
Setting up alarms for groups of people gathering in areas.
Searching for recorded face detection events and associated video.
Searching for specific behavioral patterns detected by VCA.
Setting up basic network parameters like IP address and working mode.
Setting up advanced network connections like PPPoE and DDNS.
Preparing new hard drives for use by initializing them.
Setting HDD properties like Read-only, Redundancy, or R/W.
Performing S.M.A.R.T. and Bad Sector Detection for HDD health.
Updating the NVR's firmware from local or FTP sources.
Creating and managing user accounts with different permission levels.
Guide to setting the initial administrator password for device security.
Steps for initial NVR setup using the configuration wizard.
Steps to activate IP cameras before adding them to the NVR.
Methods for adding IP cameras detected on the network.
Modifying parameters and configuring custom protocols for connected IP cameras.
Configuring cameras connected via the NVR's Power over Ethernet ports.
Configuring cameras connected via the NVR's integrated network switch ports.
Setting up parameters for controlling PTZ cameras.
Adjusting video quality settings like resolution and bitrate.
Setting up scheduled recording times and types.
Setting up recording triggered by motion detection events.
Configuring recording based on external alarm inputs.
Setting up recording for Video Content Analysis events.
Accessing and reviewing recorded video files.
Searching and playing back recordings based on date and time.
Searching recordings based on event types like alarms or motion.
Procedures for exporting recorded video files to backup devices.
Backing up files found via normal video search.
Backing up event-related video files.
Configuring motion detection sensitivity and response actions.
Configuring handling for external sensor alarms.
Setting up alarms and responses for video signal loss.
Configuring alarms for lens tampering detection.
Defining actions like full-screen monitoring or email alerts for alarms.
Configuring alarms and actions for detecting human faces.
Setting up alarms for objects crossing a defined virtual line.
Configuring alarms for unauthorized entry into defined regions.
Setting up alarms for groups of people gathering in areas.
Searching for recorded face detection events and associated video.
Searching for specific behavioral patterns detected by VCA.
Setting up basic network parameters like IP address and working mode.
Setting up advanced network connections like PPPoE and DDNS.
Preparing new hard drives for use by initializing them.
Setting HDD properties like Read-only, Redundancy, or R/W.
Performing S.M.A.R.T. and Bad Sector Detection for HDD health.
Updating the NVR's firmware from local or FTP sources.
Creating and managing user accounts with different permission levels.
General| Model | LTN8716-P8 |
|---|---|
| Category | Network Hardware |
| Type | NVR |
| Channels | 16 |
| Video Input | 16-ch IP video input |
| Resolution | Up to 8MP |
| Decoding format | H.265, H.264 |
| Operating Humidity | 10% to 90% (non-condensing) |
| Video Output | HDMI, VGA |
| Audio Input | 1-ch RCA |
| Audio Output | 1-ch RCA |
| HDD Bays | 2 |
| Max HDD Capacity | 6TB per bay |
| Network Interface | 1 x 10/100/1000 Mbps |
| Protocols | TCP/IP, DHCP, DNS, HTTP, FTP |
| Power Supply | 100 to 240 VAC, 50 to 60 Hz |
| Operating Temperature | -10°C to +55°C (14°F to 131°F) |
To Next Page
