What to do if Mafell MT 55 cc Saw cannot be switched on?
If your Mafell Saw won't switch on, there are several potential causes. First, check the power supply to ensure there is mains voltage. If the power supply is ok, inspect the mains fuse and replace it if defective. Finally, the carbon brushes may be worn, in which case you should take the machine to a MAFELL customer service shop.
Why does my Mafell Saw stop while cutting?
If your Mafell Saw stops during cutting, it could be due to a mains failure. Check the mains back-up fuses. Alternatively, the machine might be overloaded, in which case you should reduce the feed speed.
What to do if Mafell Saw blade jams as the machine is advanced?
If the saw blade jams as the Mafell Saw is advanced, consider these potential causes and solutions: * The feed rate may be too fast. Try reducing the feed speed. * The saw blade may be blunt. Immediately release the switch, remove the machine from the workpiece, and replace the saw blade. * Poor machine guidance. Use a parallel guide fence. * Uneven workpiece surface. Straighten the surface.
How to prevent burn marks on cut surfaces with Mafell Saw?
Burn marks on the cut surfaces when using the Mafell Saw can be caused by using a saw blade that is unsuitable for the task or is blunt. The solution is to replace the saw blade.
What to do if chip ejection is blocked in Mafell MT 55 cc Saw?
If the chip ejection is blocked in your Mafell Saw, it might be due to the wood being too damp. Another possible cause is extended operation without exhaustion. To resolve this, connect the saw to an external exhaustion system, such as a portable dust extractor.
What to do if my Mafell Saw stops while cutting?
If your Mafell Saw stops during cutting, it could be due to a few reasons. First, there might be a mains failure; in this case, have your mains-side pre-fuses checked by an electrician. Another possibility is that the machine is overloaded. Try reducing the feed speed or allow the machine some time to cool down. Lastly, worn carbon brushes can also cause this issue. If that's the case, take the machine to a MAFELL customer service shop.
Why won't my Mafell Saw switch on?
If your Mafell Saw won't switch on, several factors could be at play. It could be due to no mains voltage or the mains voltage being too low, so have the power supply checked by an electrician. Another cause might be a defective mains fuse; have the fuse replaced by an electrician. Finally, worn carbon brushes could be the culprit, requiring you to take the machine to a MAFELL customer service shop.
What to do if the saw blade jams on my Mafell MT 55 cc?
If the saw blade jams as the machine is advanced, consider these possibilities: The feed rate might be too fast, so reduce the feed speed. The saw blade could be blunt; in this case, release the switch immediately, remove the machine from the workpiece, and replace the saw blade. There might be tension in the workpiece, so heightened caution during sawing is needed, as the risk of backlash increases. Poor machine guidance, such as free-hand guidance, can also cause jamming, so use a parallel guide fence. Finally, an uneven workpiece surface could be the problem, so straighten the surface.
What causes burn marks on wood when using my Mafell Saw?
Burn marks on the cut surfaces when using your Mafell Saw can occur if the saw blade used is unsuitable for the task or if it is blunt. Replace the saw blade to resolve this issue.
Why does my Mafell MT 55 cc blade vibrate in the workpiece?
If your Mafell Saw blade vibrates in the workpiece, it could be due to the saw blade not being correctly adjusted; retighten the saw blade. Another reason might be that the workpiece is not fastened, so fasten the workpiece with clamps.
Rules for operating the machine safely, including supervision and modifications.
Recommends wearing ear protection and dust masks during operation.
Explains kickback phenomena and how to avoid them.
Details on checking and operating the lower guard for safety.
Guidance on choosing the correct saw blade for different materials and cuts.
How to operate the power switch and auto-brake feature.
How to set the cutting depth, including recommendations for material thickness.
General| Cutting Depth at 90° (with guide track) | 55 mm |
|---|---|
| Blade Diameter | 160 mm |
| Universal motor | Yes |
| Saw blade bore | 20 mm |
| Bevel range | 0 - 45° |
To Next Page
