Magnetek G+ - User Manual

OVERVIEW
The following procedure is a supplement to other documentation available
for the G+ Mini drive. This will guide the user in proper installation and setup
of the system.
When installing the system, be sure to follow good wiring practices and
follow all applicable electrical codes. Ensure that the mounting of all
components are secure and the environment, such as excessive moisture,
poor ventilation, etc., will not cause system degradation.
Read this document, provided with the G+ Mini, thoroughly before
attempting installation. Refer to the technical manual, as needed, available
at:
http://www.magnetekmh.com/Material%20Handling/Product%20Manuals
Step 1
Connect Motor and Line Power
Figure 1 shows the electrical connections for the input power and motor
terminals on the G+ Mini drive. Make the appropriate connections, with
power turned off. Follow good wiring practices and follow all applicable
electrical codes. Ensure the equipment is properly grounded, as shown.
Figure 1: Input Power and Output Motor Connections
DANGER! DANGEROUS VOLTAGES ARE PRESENT WHEN DRIVE
IS ON. Improper wiring can cause bodily harm and damage to the
equipment. Before applying power to the G+ Mini, ensure that all
protective covers are fastened and all wiring connections are
secure. After power has been turned OFF, wait at least 5
minutes until the charge indicator extinguishes completely before
touching any wiring, circuit boards, or components.
WARNING: DO NOT CONNECT ANY OF THE FOLLOWING
TERMINALS TO EARTH GROUND.
Step 2
Typical Connection Diagram
This step shows a typical wiring diagram and connection points for the G+ Mini.
Wiring connections should only be made by trained and authorized personnel
when power to the drive is turned off.
* 24VDC interface is standard. 120VAC, 42-48VAC, and 24VAC is optional.
** Optional P3S2-OUT2 card provides two 240 VAC, 1.5 Amp solid-state relay outputs
(panel-mounted).
*** In accordance with UL508C, EN954-1 Safety Category 3, and EN61508, SIL2.
Figure 2: Typical Connection Diagram
Step 3
Changing Parameters and Monitoring the G+ Mini
This step shows how to access and modify a G+ Mini parameter as well as how to
monitor G+ Mini signals such as output frequency and motor current.
Make sure all protective covers have been re-attached and power is turned on.
DO NOT RUN THE MOTOR.
Accessing Parameter Menu & Changing Parameters
Figure 3: G+ Mini Digital Operator Power-up State
Press four times until the digital operator shows the parameter menu (PAr)
then press .
Figure 4: Select Parameter Value
Press to select the digit you would like to change. Next use and to
select the parameter group, sub-group, or number.
Figure 5: Select Parameter
Modify the parameter value using and . Press to save the new
value.
Figure 6: Change Parameter Value
Press ESC several times to return to the main display.
P.O. Box 13615
Milwaukee, WI 53213
Toll-Free Phone: 800-288-8178
Toll-Free Fax: 800-298-3503
N49 W13650 Campbell Drive
Menomonee Falls, WI 53051
Phone: 262-783-3500
Fax: 262-783-3510
Unit 3 Bedford Business Centre Mile Road
Bedford, MK42 9TW UK
Phone: +44-1234-349191
Fax: +44-1234-268955
www.magnetek.com
Instruction Sheet No. 144-25543
G+ Mini Drive
Quick Start Guide

Summary

Overview and Safety

DANGER! Dangerous Voltages

Warning about dangerous voltages and safety precautions before touching components.

Installation Best Practices

Guidelines for secure mounting, wiring, and environmental considerations during installation.

Connecting Motor and Line Power

Electrical Connections

Details electrical connections for input power and motor terminals on the G+ Mini drive.

Grounding Warning

Specific warning against connecting certain terminals to earth ground.

Typical Connection Diagram

Changing Parameters and Monitoring

Accessing Parameter Menu

Guide on how to access and modify G+ Mini parameters.

Selecting Parameter Value

Instructions on how to select and adjust parameter values.

Saving New Parameter Values

Steps to save modified parameter values using the operator.

Monitoring Motor Frequency and Current

Displaying Output Frequency

Procedure to display the actual drive output frequency in Hz.

Displaying Motor Current

Procedure to display the motor output current in Amps.

Selecting Control Method and Motion

Selecting Speed Reference

Auto-Tuning Procedure

Auto-Tuning Setup

Instructions for setting up the G+ Mini for auto-tuning with the motor.

Auto-Tuning Safety Warnings

Warnings about potential sudden movement and electric shock during auto-tuning.

Executing Auto-Tuning

Steps to initiate and run the auto-tuning process via the operator.

Quick Start Parameters and FAQ

Quick Start Parameter Table

Lists general purpose application parameters and their settings.

Frequently Asked Questions

Answers common questions regarding drive settings and operation.

Magnetek G+ Specifications

General

Brand	Magnetek
Model	G+
Category	DC Drives
Language	English