EasyManuals Logo

Makita 9565CLR User Manual

Makita 9565CLR
76 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
11
cut and the possibility of kickback, wheel breakage and
overheating of the motor may occur.
Do not start the cutting operation in the workpiece. Let
the wheel reach full speed and carefully enter into the
cut moving the tool forward over the workpiece surface.
The wheel may bind, walk up or kickback if the power
tool is started in the workpiece.
During cutting operations, never change the angle of
the wheel. Placing side pressure on the cut-off wheel
(as in grinding) will cause the wheel to crack and break,
causing serious personal injury.
A diamond wheel shall be operated perpendicular to
the material being cut.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
The tool and its air vents have to be kept clean.
Regularly clean the tool’s air vents or whenever the vents
start to become obstructed. (Fig. 24)
When head cover is installed on the tool, remove it with
referring to “Removing head cover”.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Wheel guard (Wheel cover) For depressed center
wheel/Multi disc
Wheel guard (Wheel cover) For abrasive cut-off wheel/
diamond wheel
Depressed center wheels
Abrasive cut-off wheels
•Multi discs
Diamond wheels
Wire cup brushes
Wire bevel brush 85
Abrasive discs
Inner flange
Lock nut For depressed center wheel/abrasive cut-off
wheel/multi disc/diamond wheel
Lock nut For abrasive disc
Lock nut wrench
Side grip
Rubber pad
Dust cover attachment
NOTE:
Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
ENG905-1
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
): 86 dB (A)
Sound power level (L
WA
): 97 dB (A)
Uncertainty (K): 3 dB (A)
Wear ear protection.
Vibration
ENG900-1
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: surface grinding
Vibration emission (a
h,AG
): 4.5 m/s
2
Uncertainty (K): 1.5 m/s
2
Work mode: disc sanding
Vibration emission (a
h,DS
): 2.5 m/s
2
or less
Uncertainty (K): 1.5 m/s
2
ENG902-1
The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
The declared vibration emission value is used for main
applications of the power tool. However if the power
tool is used for other applications, the vibration
emission value may be different.
WARNING:
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
ENH101-18
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Angle Grinder
Model No./Type: 9565CLR
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Makita 9565CLR and is the answer not in the manual?

Makita 9565CLR Specifications

General IconGeneral
BrandMakita
Model9565CLR
CategoryGrinder
LanguageEnglish

Related product manuals