11 ENGLISH
Checking proper action before
operation
Bef ore operation, alw ay s c h ec k f ollow ing points.
— Make sure th at th e tool d oes not operate only by
c onnec ting th e air h ose.
— Make sure th at th e tool d oes not operate only by
pulling th e trigger.
— Make sure th at th e tool d oes not operate only by
plac ing th e c ontac t element against th e w orkpiec e
w ith out pulling th e trigger.
— I n single seq uential ac tuation mod e, make sure
th at th e tool d oes not operate w h en pulling th e
trigger rst and then placing the contact element
against th e w orkpiec e.
Selecting the operation mode
CAUTION: Always make sure that the actua-
tion mode selector is properly set to the position
for the desired nailing mode before nailing.
Fig.16: 1. A c tuation mod e selec tor
Single sequential actuation mode:
Y ou c an d riv e one nail by one seq uential operation.
S elec t th is mod e w h en d riv ing a nail c aref ully and
ac c urately .
T o c h oose th is mod e, set th e ac tuation mod e selec tor to
th e
position.
Contact actuation mode:
Y ou c an d riv e nails repetitiv ely by plac ing th e c ontac t
element w ith th e trigger h eld .
T o c h oose th is mod e, set th e ac tuation mod e selec tor to
th e
position.
Single sequential actuation
CAUTION: Do not place the contact element
against the workpiece with excessive force. Also,
pull the trigger fully and hold it on for 1-2 seconds
after nailing.
Ev en in th e “ S ingle seq uential ac tuation” mod e, h alf -
pulled trigger c auses an unex pec ted nailing, w h en th e
c ontac t element re-c ontac ts th e w orkpiec e.
P lac e th e c ontac t element against th e w orkpiec e and
pull th e trigger f ully .
A f ter nailing, release th e c ontac t element, and th en
release th e trigger.
Fig.17
Contact actuation
Pull the trigger rst and then place the contact element
against th e w orkpiec e.
Fig.18
Anti dry re mechanism
This tool is equipped with an anti dry re mechanism.
W h en th ere are a f ew nails remaining in th e magaz ine,
th e c ontac t arm w ill be loc ked in th e und epressed posi-
tion to prev ent th e tool f rom being ac tiv ated . W h en it is
ac tiv ated , load more nails to resume operation.
Removing jammed nails
CAUTION: Always release the trigger and dis-
connect the hose before removing jammed nails.
CAUTION: Do not use deformed nails or nail
strip. F ailure to d o so c auses poor nail f eed ing.
W h en th e nailer bec omes j ammed , d o as f ollow s:
I nsert a small rod or th e like into th e ej ec tion port and
tap it w ith a h ammer to retrac t th e d riv er.
Fig.19: 1. H ammer 2. S mall rod 3. Ej ec tion port
4. D riv er
U se pliers to bend th e j ammed nail so th at th e nail h ead
c omes out of th e slot in th e d riv er guid e. T h en remov e
th e j ammed nail.
Fig.20: 1. P liers 2. S lot
MAINTENANCE
CAUTION: Before attempting to perform
inspection or maintenance, always release the
trigger and disconnect the air hose from the tool.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Nails
H and le nail strips and th eir box c aref ully . I f th e nail
strips h av e been h and led rough ly , th ey may be out of
sh ape, c ausing poor nail f eed .
A v oid storing nails in a v ery h umid or h ot plac e or plac e
ex posed to d irec t sunligh t.
Maintenance of nailer
A lw ay s c h ec k th e tool f or its ov erall c ond ition and loose
sc rew s bef ore operation. T igh ten as req uired .
W ith tool d isc onnec ted , make d aily inspec tion to assure
f ree mov ement of th e c ontac t element and trigger. D o
not use tool if th e c ontac t element or trigger stic ks or
bind s.
W h en th e tool is not to be used f or an ex tend ed period
of time, lubric ate th e tool using pneumatic tool oil and
store th e tool in a saf e plac e. A v oid ex posure to d irec t
sunligh t and / or h umid or h ot env ironment.
Fig.21
To Next Page
Loading...
