EasyManuals Logo

Makita DSP601ZJU2 User Manual

Makita DSP601ZJU2
156 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
14 ENGLISH
NOTE:Dependingontheconditionsofuseandthe
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Automatic speed change function
NOTE:Automaticspeedchangefunctionisonly
availablewhenthespeedadjustingdialisin5.
Thistoolhas"highspeedmode"and"hightorque
mode".
Thetoolautomaticallychangestheoperationmode
depending on the work load. When the work load is low,
thetoolwillruninthe"highspeedmode"forquicker
cutting operation. When the work load is high, the tool
willruninthe"hightorquemode"forpowerfulcutting
operation.
►Fig.10: 1. Mode indicator
Themodeindicatorlightsupingreenwhenthetoolis
runningin"hightorquemode".
Ifthetoolisoperatedwithexcessiveload,themode
indicatorwillblinkingreen.Themodeindicatorstops
blinkingandthenlightsuporturnsoffifyoureducethe
load on the tool.
Mode indicator status Operation
mode
On Off Blinking
High speed
mode
Hightorque
mode
Overload
alert
Adjusting depth of cut
CAUTION: After adjusting the depth of cut,
always tighten the clamping screw securely.
Loosen the clamping screw on the depth guide and
move the blade lower limit stopper to the desired depth
onthescaleplate.Atthedesireddepthofcut,tighten
theclampingscrewrmly.
Forcleaner,safercuts,setcutdepthsothatnomore
thanonebladetoothprojectsbelowworkpiece.Using
propercutdepthhelpstoreducepotentialfordanger-
ousKICKBACKSwhichcancausepersonalinjury.
►Fig.11: 1. Blade lower limit stopper 2. Clamping
screw
Quick stop button for 2 to 3 mm
depth of cut when using guide rail
(optional accessory)
Thistoolhasthequickstopbuttonfor2to3mmdepth
ofcutonthegearhousingasidetherearhandlewhen
usingguiderail.Thisisusedwhenavoidingsplinteron
theworkpieceinthecut.Makeapassofthe2to3mm
rstcutandthenmakeanotherpassofusualcut.
►Fig.12: 1. Quick stop button
Toobtainthe2to3mmdepthofcut,pushinthequick
stopbuttontowardthesawblade.Thisisconvenientfor
avoiding splinter on the workpiece.
Toreleasethedepthofcutfromthispositionforfree
depthofcut,justpullthebuttonback.
Bevel cutting
Loosentheclampingscrews.Setforthedesiredangle
by tilting accordingly, then tighten the clamping screws
securely.
►Fig.13: 1. Clamping screw 2. Bevel scale plate
►Fig.14: 1.Subbase(Optionalaccessory)
2. Clamping screw
Positive stopper
Thepositivestopperisusefulforsettingthedesignated
anglequickly.Turnthepositivestoppersothatthe
arrow on it points 22.5°. Loosen the clamping screws
infrontandback.Thentiltthebladeuntilitstopsand
secure the base with the clamping screws.
►Fig.15: 1. Positive stopper 2. Clamping screw
48°-bevel cutting
Toperform48°-bevelcutting,loosentheclamping
screwsandfullytiltthelevertowardthedirectionofthe
arrowinthegure.Thensetthebevelangleto48°and
tighten the clamping screws.
►Fig.16: 1. Lever
-1°-bevel cutting
Toperform-1°-bevelcutting,loosentheclamping
screwsandpresstheleverstowardthedirectionofthe
arrowinthegure.Thensetthebevelangleto-1°and
tighten the clamping screws.
►Fig.17: 1. Lever
Sighting
►Fig.18: 1. Base
Thecuttinglinevariesdependingonthecuttingangle
andwhetheryouusetheguiderail(optionalaccessory).
When using the tool without guide rail
Forstraightcuts,aligntheApositiononthefrontofthe
base with your cutting line. For 45° bevel cuts, align the
B position with it.
When using the tool with guide rail
For both straight cuts and 45° bevel cuts, always align
theApositiononthefrontofthebasewithyourcutting
line.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Makita DSP601ZJU2 and is the answer not in the manual?

Makita DSP601ZJU2 Specifications

General IconGeneral
BrandMakita
ModelDSP601ZJU2
CategorySaw
LanguageEnglish

Related product manuals