EasyManuals Logo

Makita DSP601ZJU2 User Manual

Makita DSP601ZJU2
156 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #16 background imageLoading...
Page #16 background image
16 ENGLISH
Blade guard cleaning
When changing the circular saw blade, make sure to
alsocleanthebladeguardofaccumulatedsawdustas
discussedintheMaintenancesection.Sucheffortsdo
notreplacetheneedtocheckguardoperationbefore
each use.
Connecting a vacuum cleaner
Optional accessory
Whenyouwishtoperformcleancuttingoperation,
connect a Makita vacuum cleaner to your tool. Connect
ahoseofthevacuumcleanertothedustnozzleusing
thefrontcuff24.
►Fig.25: 1.Hoseofthevacuumcleaner2.Frontcuff
24 3.Dustnozzle
OPERATION
CAUTION: Be sure to move the tool forward
in a straight line gently. Forcing or twisting the tool
will result in overheating the motor and dangerous
kickback,possiblycausingsevereinjury.
CAUTION: Never approach any part of your
body under the tool base when section cutting,
especially at starting. Doing so may cause seri-
ous personal injuries.Thebladeisexposedunder
the tool base.
NOTE: When the battery cartridge temperature is
low,thetoolmaynotworktoitsfullcapacity.Atthis
time,forexample,usethetoolforalight-dutycutfor
a while until the battery cartridge warms up as high
asroomtemperature.Then,thetoolcanworktoits
fullcapacity.
Section cutting (ordinary sawing)
►Fig.26
Holdthetoolrmly.Thetoolisprovidedwithbothafront
grip and rear handle. Use both to best grasp the tool.
Ifbothhandsareholdingsaw,theycannotbecutby
the circular saw blade. Set the base on the workpiece
to be cut without the circular saw blade making any
contact.Thenpushinthelock-offbuttonandpullthe
switch trigger. Wait until the circular saw blade attains
fullspeed.Nowpressdownthesawheadslowlytothe
presetdepthofcutandsimplymovethetoolforward
overtheworkpiecesurface,keepingitatandadvanc-
ing smoothly until the sawing is completed.
Togetcleancuts,keepyoursawinglinestraightand
yourspeedofadvanceuniform.Ifthecutfailstoprop-
erlyfollowyourintendedcutline,donotattempttoturn
orforcethetoolbacktothecutline.Doingsomaybind
the circular saw blade and lead to dangerous kickback
andpossibleseriousinjury.Releasetheswitch,wait
forthecircularsawbladetostopandthenwithdraw
the tool. Realign the tool on new cut line, and start
cutagain.Attempttoavoidpositioningwhichexposes
operatortochipsandwooddustbeingejectedfromthe
saw.Useeyeprotectiontohelpavoidinjury.
Guide rail
Optional accessory
Placethetoolontherearendofguiderail.Turntwo
adjustingscrewsonthetoolbasesothatthetoolslides
smoothlywithoutaclatter.Holdboththefrontgripand
rearhandleofthetoolrmly.Turnonthetool,pressdown
the tool to the preset cutting depth and cut the splinter-
guardalongthefulllengthwithastroke.Nowtheedgeof
the splinterguard corresponds to the cutting edge.
►Fig.27: 1.Adjustingscrews
When bevel cutting with the guide rail, use the slide
levertopreventthetoolfromfallingover.
Movetheslideleveronthetoolbaseinthedirectionofarrow
so that it engages the undercut groove in the guide rail.
►Fig.28: 1. Slide lever
Sub base (Guide rule)
Optional accessory
Byusingthesubbaseasaguiderule,youcanperform
extra-accurate straight cuts. Loosen the clamping
screwsandslidethesubbaseoutfromthetoolthen
insert it upside down.
►Fig.29: 1. Clamping screw 2. Sub base
Simplyslidethefenceofthesubbasesnuglyagainst
thesideoftheworkpieceandsecureitinpositionwith
theclampingscrews.Italsomakesrepeatedcutsof
uniformwidthpossible.
►Fig.30: 1. Clamping screw 2. Sub base
Plunge cutting (Cutting-out)
WARNING: To avoid a kickback, be sure to
observe the following instructions.
►Fig.31: 1.Rearedgeoftoolbase2. Fixed stop
When using the tool without guide rail, place the tool on
theworkpiecewiththerearedgeoftoolbaseagainsta
xedstoporequivalentwhichisdevisedbyanoperator.
When using the tool with guide rail, place the tool on the
guiderailwiththerearedgeoftoolbaseagainstaxed
stoporequivalentwhichisclampedontheguiderail.
Holdthetoolrmlywithonehandonthefrontgripand
theotheronthetoolhandle.Thenpushinthelock-off
button and turn the tool on and wait until the blade
attainsfullspeed.Nowpressdownthesawheadslowly
tothepresetdepthofcutandsimplymovethetool
forwardtothedesiredplungeposition.
NOTE:
Themarkingsonthesideofthebladeguard
showthefrontandrearcuttingpointsofthesawblade
at the maximum cutting depth when using the guide rail.
►Fig.32: 1. Front cutting point 2. Rear cutting point
Guide device
Optional accessory
Useofthebevelguideallowsexactmitercutswith
anglesandttingworks.
Useoftheclampensuresrmholdofworkpieceonthe
table.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Makita DSP601ZJU2 and is the answer not in the manual?

Makita DSP601ZJU2 Specifications

General IconGeneral
BrandMakita
ModelDSP601ZJU2
CategorySaw
LanguageEnglish

Related product manuals