EasyManua.ls Logo

Makita DUC254 - User Manual

Makita DUC254
203 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
EN
Cordless Chain Saw
INSTRUCTION MANUAL
8
FR
Tronçonneuse sans Fil
MANUEL D’INSTRUCTIONS
DE
Akku-Kettensäge
BETRIEBSANLEITUNG
IT
Motosega a batteria
ISTRUZIONI PER L’USO
NL
Accukettingzaag
GEBRUIKSAANWIJZING
ES
Electrosierra Inalámbrica
MANUAL DE
INSTRUCCIONES
PT
Motosserra a Bateria
MANUAL DE INSTRUÇÕES
DA
Akku-kædesav
BRUGSANVISNING
EL
Φορητό αλυσοπρίονο
ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ
110
TR
Akülü Ağaç Kesme
KULLANMA KILAVUZU
124

Table of Contents

Questions and Answers

  • B
    Bruce BakerSep 8, 2025
    Why is the main power lamp blinking green on my Makita DUC254?
    • S
      Steven GarciaSep 8, 2025
      If the main power lamp on your Makita Chainsaw is blinking green, it means that the switch trigger is being pulled under an inoperable condition. Pull the switch trigger after the main power switch is turned on and the chain brake is released.
  • B
    Bonnie BowenAug 25, 2025
    Why does my Makita DUC254 not start?
    • G
      Gina HallAug 25, 2025
      Your Makita Chainsaw might not be starting due to several reasons: the battery cartridge may not be installed—install a charged battery cartridge. There could be a battery problem, such as low voltage—recharge the battery cartridges, or replace them if recharging isn't effective. Alternatively, the main power switch might be off—turn the main power switch on.
  • E
    Ethan MartinezAug 25, 2025
    How to troubleshoot a Makita Chainsaw that does not start?
    • W
      William FordAug 26, 2025
      If your Makita Chainsaw does not start, a possible cause is that the battery cartridge is not installed. To fix this, install a charged battery cartridge. Another reason could be a battery problem such as low voltage. In this case, try recharging the battery cartridges; if that doesn't work, replace the battery cartridge. Also, the main power switch might be off. If so, turn the main power switch on again, as the chainsaw automatically turns off if left unused for a while.
  • S
    scottcarolSep 18, 2025
    Why doesn't my Makita Cordless Saw reach maximum RPM?
    • K
      ksnyderSep 18, 2025
      If your Makita Cordless Saw isn't reaching maximum RPM, it could be due to a few reasons: the battery cartridge might be installed improperly (install the battery cartridges correctly), or the battery power may be dropping (recharge or replace the battery cartridge). If these steps don't resolve the issue, ask the authorized service center in your region for repair.
  • L
    Leah PollardSep 8, 2025
    Why is the Torque Boost mode not available on my Makita DUC254 Chainsaw?
    • J
      Jason SalazarSep 9, 2025
      If the Torque Boost mode is not available on your Makita Chainsaw after replacing the battery cartridge, use the tool in the normal mode until the installed battery cartridge becomes empty, and then replace the battery cartridge with a fully charged one, or recharge the battery cartridge.
  • J
    Jacqueline McclureSep 13, 2025
    Why is my Makita DUC254 Chainsaw vibrating abnormally?
    • T
      Tony HaynesSep 13, 2025
      If you experience abnormal vibration with your Makita Chainsaw, stop the machine immediately! This could be due to a loose guide bar or saw chain. Adjust the guide bar and saw chain tension. If the issue persists, it may indicate a tool malfunction, and you should ask the authorized service center in your region for repair.
  • B
    Benjamin HubbardSep 3, 2025
    What to do if my Makita Cordless Saw chain is not running?
    • K
      Kenneth VelazquezSep 3, 2025
      If the saw chain on your Makita Cordless Saw isn't running, it's likely that the chain brake is activated. Release the chain brake to allow the chain to run.
  • K
    Katelyn JonesSep 4, 2025
    How to troubleshoot a Makita Cordless Saw that won't start?
    • B
      Brian ParkerSep 4, 2025
      If your Makita Cordless Saw doesn't start, here are a few things to check: * Ensure a charged battery cartridge is correctly installed. * Recharge the battery. If it remains ineffective, consider replacing the battery cartridge. * If the main power switch is off (the chainsaw automatically turns off after a period of inactivity), turn it on again.
  • M
    Mark HernandezSep 23, 2025
    What should I do if my Makita Cordless Saw has abnormal vibration?
    • K
      Kristin GarciaSep 23, 2025
      If you experience abnormal vibration with your Makita Cordless Saw, stop the machine immediately and adjust the guide bar and saw chain tension if they are loose.
  • J
    joe85Aug 29, 2025
    What to do if my Makita DUC254 Chainsaw motor stops after a little use?
    • S
      scarterAug 29, 2025
      If the motor of your Makita Chainsaw stops running after a short period, it's likely due to a low battery charge. Recharge the battery. If the issue persists after recharging, consider replacing the battery cartridge.

Summary

Specifications

SAFETY WARNINGS

General power tool safety warnings

Essential safety precautions applicable to all power tools.

Cordless Chain saw safety warnings

Specific safety instructions for operating this cordless chain saw.

Protective equipment

Lists necessary personal protective gear for safe chain saw operation.

Important safety instructions for battery cartridge

FUNCTIONAL DESCRIPTION

Installing or removing battery cartridge

Step-by-step guide on how to insert and remove the battery.

Checking the chain brake

Checking the run-down brake

ASSEMBLY

Adjusting saw chain tension

OPERATION

WORKING WITH THE CHAIN SAW

MAINTENANCE

Instructions for periodic maintenance

TROUBLESHOOTING

Makita DUC254 Specifications

General IconGeneral
Idle speed- RPM
Chain pitch3/8 \
Chain speed24 m/s
Blade length- mm
Product colorGreen
Safety switchYes
Chain bar length250 mm
Oil tank capacity0.14 L
Power sourceBattery
Battery voltage18 V
Battery includedNo
Weight and Dimensions IconWeight and Dimensions
Length256 mm
Weight2800 g

Related product manuals