To Next PageTo Next PageWhat to do if the saw chain of my Makita Chainsaw does not run?
If the chain on your Makita Chainsaw does not run, the chain brake may be activated. Release the chain brake to allow the chain to move freely.
Why is the main power lamp blinking green on my Makita DUC254?
If the main power lamp on your Makita Chainsaw is blinking green, it means that the switch trigger is being pulled under an inoperable condition. Pull the switch trigger after the main power switch is turned on and the chain brake is released.
What to do if my Makita DUC254 Chainsaw motor stops after a little use?
If the motor of your Makita Chainsaw stops running after a short period, it's likely due to a low battery charge. Recharge the battery. If the issue persists after recharging, consider replacing the battery cartridge.
What does it mean when the main power lamp is blinking green on my Makita Chainsaw?
If your Makita Chainsaw's main power lamp is blinking green, it means the switch trigger is being pulled under an inoperable condition. Ensure the main power switch is turned on and the chain brake is released before pulling the switch trigger.
What to do if the chain of my Makita DUC254 Chainsaw does not stop when the chain brake is activated?
If the chain on your Makita Chainsaw does not stop even when the chain brake is activated, the brake band is likely worn down. Ask the authorized service center in your region for repair.
Why is my Makita DUC254 Chainsaw vibrating abnormally?
If you experience abnormal vibration with your Makita Chainsaw, stop the machine immediately! This could be due to a loose guide bar or saw chain. Adjust the guide bar and saw chain tension. If the issue persists, it may indicate a tool malfunction, and you should ask the authorized service center in your region for repair.
Why is Torque Boost mode unavailable on my Makita DUC254 after battery replacement?
The Torque Boost mode on your Makita Chainsaw might not be available after replacing the battery cartridge due to usage conditions. Try using the tool in normal mode until the installed battery cartridge is empty, then replace it with a fully charged one, or recharge the battery cartridge.
Why the saw chain cannot be installed on my Makita DUC254?
If the saw chain cannot be installed on your Makita Chainsaw, the combination of saw chain and sprocket is not correct. Use the correct combination of saw chain and sprocket by referring to the section for specifications.
What to do if there is no oil on the chain of my Makita Chainsaw?
If there is no oil on the chain of your Makita Chainsaw, check the following: First, the oil tank may be empty, so fill it. Second, the oil guide groove may be dirty and needs cleaning. Third, the oil delivery might be poor, so adjust the amount of oil delivery with the adjusting screw.
How to troubleshoot a Makita Chainsaw that does not start?
If your Makita Chainsaw does not start, a possible cause is that the battery cartridge is not installed. To fix this, install a charged battery cartridge. Another reason could be a battery problem such as low voltage. In this case, try recharging the battery cartridges; if that doesn't work, replace the battery cartridge. Also, the main power switch might be off. If so, turn the main power switch on again, as the chainsaw automatically turns off if left unused for a while.
General| Idle speed | - RPM |
|---|---|
| Chain pitch | 3/8 \ |
| Chain speed | 24 m/s |
| Blade length | - mm |
| Product color | Green |
| Safety switch | Yes |
| Chain bar length | 250 mm |
| Oil tank capacity | 0.14 L |
| Power source | Battery |
| Battery voltage | 18 V |
| Battery included | No |
Weight and Dimensions| Length | 256 mm |
|---|---|
| Weight | 2800 g |
Essential safety precautions applicable to all power tools.
Specific safety instructions for operating this cordless chain saw.
Lists necessary personal protective gear for safe chain saw operation.
Step-by-step guide on how to insert and remove the battery.
