To Next PageTo Next PageWhy won't my Makita DUC353PT4J Chainsaw start?
Your Makita Chainsaw might not start due to several reasons: First, ensure that two charged battery cartridges are properly installed. Second, the battery voltage may be low, requiring you to recharge or replace the battery cartridges. Finally, check if the main power switch is turned off, as the chainsaw automatically turns off after a period of inactivity. Turn the main power switch on again.
Why my Makita Chainsaw does not start?
Your Makita Chainsaw might not start because two battery cartridges are not installed. Make sure to install two charged battery cartridges. Another reason could be a battery problem, such as low voltage. In this case, recharge the battery cartridges, and if that doesn't work, replace them. Also, the main power switch may be off. If the chainsaw is left un-operated for a while, it automatically turns off, so turn the main power switch on again.
How to fix no oil on chain of Makita DUC353PT4J?
If there's no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so you should fill it. Another possible cause is a dirty oil guide groove, which requires cleaning. Also, check the oil delivery and adjust the amount of oil delivered with the adjusting screw.
What to do if there is no oil on the Makita DUC353PT4J Chainsaw chain?
If there's no oil on the chain of your Makita Chainsaw, it could be due to several reasons. First, check if the oil tank is empty and fill it if needed. Another possibility is that the oil guide groove is dirty, so try cleaning it. Finally, there might be poor oil delivery, in which case you should adjust the amount of oil delivery with the adjusting screw.
What to do if my Makita DUC353PT4J motor stops running after a little use?
If the motor of your Makita Chainsaw stops running after a short period, the battery's charge level may be low. Recharge the battery cartridges. If recharging isn't effective, consider replacing the battery cartridge.
What to do if my Makita Chainsaw chain does not run?
If the saw chain of your Makita Chainsaw does not run, the chain brake may be activated. Ensure that you release the chain brake.
Why is there no oil on the chain of my Makita DUC353PT4J Chainsaw?
If there's no oil on the chain of your Makita Chainsaw, it could be due to several reasons. First, check if the oil tank is empty and fill it if needed. Second, the oil guide groove might be dirty, so clean the groove. Finally, there might be poor oil delivery; in this case, adjust the amount of oil delivery using the adjusting screw.
What to do if Makita Chainsaw motor stops after short use?
If the motor of your Makita Chainsaw stops running after a short period, it's likely due to a low battery charge level. Try recharging the battery cartridges. If recharging doesn't solve the problem, consider replacing the battery cartridge.
Why my Makita DUC353PT4J does not reach maximum RPM?
If your Makita Chainsaw isn't reaching maximum RPM, it could be due to a few reasons. First, make sure the battery cartridge is correctly installed as described in this manual. Another reason may be that the battery power is dropping, so try recharging the battery cartridges, and if that doesn't work, replace them. If these steps don't resolve the issue, it may be a problem with the drive system.
What causes abnormal vibration in Makita DUC353PT4J?
Abnormal vibration in your Makita Chainsaw can be caused by a loose guide bar or saw chain. In this case, you should adjust the guide bar and saw chain tension.
General| Battery Voltage | 36 V |
|---|---|
| Bar Length | 35 cm |
| Chain Pitch | 3/8 " |
| Chain Gauge | 1.3 mm |
| Battery Type | Li-ion |
| Automatic Oil Supply | Yes |
| Chain Brake | Yes |
| Vibration Level | 2.5 m/s² |
| Type | Cordless Chainsaw |
