Makita DUC355PT2 - User Manual

Questions and Answers

E
emilyhessAug 18, 2025
Why my Makita Chainsaw does not start?
- J
  jeffrey99Aug 18, 2025
  Your Makita Chainsaw might not start because two battery cartridges are not installed. Make sure to install two charged battery cartridges. Another reason could be a battery problem, such as low voltage. In this case, recharge the battery cartridges, and if that doesn't work, replace them. Also, the main power switch may be off. If the chainsaw is left un-operated for a while, it automatically turns off, so turn the main power switch on again.
W
wilsonlindsayAug 21, 2025
Why won't my Makita Chainsaw start?
- J
  John RoweAug 21, 2025
  Your Makita Chainsaw might not start due to several reasons: First, ensure that two charged battery cartridges are properly installed. Second, the battery voltage may be low, requiring you to recharge or replace the battery cartridges. Finally, check if the main power switch is turned off, as the chainsaw automatically turns off after a period of inactivity. Turn the main power switch on again.
G
gandersonAug 23, 2025
What to do if there is no oil on the Makita DUC355PT2 chain?
- A
  Angel PetersenAug 23, 2025
  If there's no oil on the chain of your Makita Chainsaw, it could be due to several reasons. First, check if the oil tank is empty and fill it if needed. Another possibility is that the oil guide groove is dirty, so try cleaning it. Finally, there might be poor oil delivery, in which case you should adjust the amount of oil delivery with the adjusting screw.
E
Elizabeth HughesAug 26, 2025
How to fix no oil on chain of Makita Chainsaw?
- V
  Vanessa EllisAug 26, 2025
  If there's no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so you should fill it. Another possible cause is a dirty oil guide groove, which requires cleaning. Also, check the oil delivery and adjust the amount of oil delivered with the adjusting screw.
T
Tammy BuckAug 28, 2025
What to do if Makita Chainsaw motor stops after short use?
- M
  Margaret BairdAug 28, 2025
  If the motor of your Makita Chainsaw stops running after a short period, it's likely due to a low battery charge level. Try recharging the battery cartridges. If recharging doesn't solve the problem, consider replacing the battery cartridge.
B
bloweAug 30, 2025
Why does my Makita DUC355PT2 motor stop running quickly?
- M
  Mason MooneyAug 30, 2025
  If the motor of your Makita Chainsaw stops running after only a short period of use, the battery's charge level is likely low. Recharge the battery cartridges, and if recharging isn't effective, consider replacing the battery cartridge.
M
mosestamaraSep 2, 2025
How to fix a Makita DUC355PT2 that does not reach maximum RPM?
- A
  Ashlee CollinsSep 2, 2025
  If your Makita Chainsaw isn't reaching its maximum RPM, it could be due to a few reasons. First, ensure that the battery cartridge is installed correctly. If the battery power is dropping, try recharging the battery cartridges or replacing them if recharging is not effective.
L
lewishollySep 4, 2025
What to do if the Makita DUC355PT2 chain does not run?
- J
  Jay WilsonSep 4, 2025
  If the saw chain on your Makita Chainsaw isn't running, the chain brake might be activated. Try releasing the chain brake.
A
Antonio BellSep 7, 2025
What causes abnormal vibration in Makita DUC355PT2 Chainsaw?
- M
  Michael WellsSep 7, 2025
  Abnormal vibration in your Makita Chainsaw can be caused by a loose guide bar or saw chain. Try adjusting the guide bar and saw chain tension.
D
Daniel GarnerSep 10, 2025
Why is the main power lamp blinking on my Makita Chainsaw?
- C
  Colleen AllenSep 10, 2025
  The main power lamp on your Makita Chainsaw might be blinking because the switch trigger is being pulled under an un-operable condition. Make sure to pull the switch trigger only after the main power switch is turned on and the chain brake is released.

Summary

Safety Warnings

General Power Tool Safety

Essential safety instructions for all power tools, including reading manuals and proper use.

Work Area Safety

Guidelines for maintaining a safe and clean work environment to prevent accidents.

Electrical Safety

Precautions related to electrical connections and avoiding electric shock.

Personal Safety

User safety guidelines including alertness, PPE, and preventing unintentional starts.

Power Tool Use and Care

Battery Tool Use and Care

Cordless Chain Saw Specific Safety

Crucial safety warnings and operating procedures specific to the cordless chain saw.

Important Battery Cartridge Safety

Critical safety instructions for handling, storing, and disposing of battery cartridges.

Functional Description

Tool and Battery Protection System

Explanation of the tool's protection systems: overload, overheat, and overdischarge.

Switch Action and Safety Features

Operation and Assembly

Checking the Run-Down Brake

Adjusting Saw Chain Tension

Instructions for properly tensioning the saw chain to ensure safe and efficient operation.

Working with the Chain Saw

Bucking (Cutting Logs)

Techniques for safely cutting logs and timber.

Limbing Branches

Burrowing and Felling Techniques

Specialized cutting techniques and safety precautions for felling trees.

Maintenance and Sharpening

Saw Chain Sharpening

General Maintenance Procedures

Periodic Maintenance Schedule

Troubleshooting

Malfunction Diagnosis and Actions

Common problems, their causes, and recommended actions to resolve them.