What to do if Makita Chainsaw chain doesn't stop when brake is on?
If the chain of your Makita chainsaw does not stop even when the chain brake is activated, stop the machine immediately! The brake band may be worn down, so ask the authorized service center in your region for repair.
Why my Makita DUC355 does not start?
Your Makita Chainsaw might not start because two battery cartridges are not installed. Make sure to install two charged battery cartridges. Another reason could be a battery problem, such as low voltage. In this case, recharge the battery cartridges, and if that doesn't work, replace them. Also, the main power switch may be off. If the chainsaw is left un-operated for a while, it automatically turns off, so turn the main power switch on again.
What to do if my Makita Chainsaw chain is not getting oil?
If there is no oil on the chain of your Makita chainsaw: * Check if the oil tank is empty and fill it if needed. * Inspect the oil guide groove for dirt and clean it. * Adjust the amount of oil delivery with the adjusting screw if the oil delivery is poor.
What to do if my Makita Chainsaw motor stops quickly after starting?
If the motor of your Makita Chainsaw stops running soon after you start using it, it could be due to a low battery charge. Try recharging the battery cartridges. If recharging doesn't solve the issue, consider replacing the battery cartridge.
How to fix no oil on chain of Makita Chainsaw?
If there's no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so you should fill it. Another possible cause is a dirty oil guide groove, which requires cleaning. Also, check the oil delivery and adjust the amount of oil delivered with the adjusting screw.
What to do if Makita DUC355 Chainsaw motor stops after short use?
If the motor of your Makita Chainsaw stops running after a short period, it's likely due to a low battery charge level. Try recharging the battery cartridges. If recharging doesn't solve the problem, consider replacing the battery cartridge.
How to fix a Makita Chainsaw that does not reach maximum RPM?
If your Makita Chainsaw isn't reaching its maximum RPM, it could be due to a few reasons. First, ensure that the battery cartridge is installed correctly. If the battery power is dropping, try recharging the battery cartridges or replacing them if recharging is not effective.
What to do if the Makita DUC355 Chainsaw chain does not run?
If the saw chain on your Makita Chainsaw isn't running, the chain brake might be activated. Try releasing the chain brake.
What to do if Makita DUC355 Chainsaw has abnormal vibration?
If your Makita chainsaw experiences abnormal vibration, stop using it immediately! This could be due to a loose guide bar or saw chain. Adjust the guide bar and saw chain tension. If the issue persists, it may indicate a tool malfunction, ask the authorized service center in your region for repair.
Why is my Makita DUC355 main power lamp blinking?
The main power lamp on your Makita chainsaw might be blinking because the switch trigger is being pulled when the tool is not ready. Ensure the main power switch is on and the chain brake is released before pulling the switch trigger.
Outlines fundamental safety rules applicable to all power tools.
Explains kickback and how operators can prevent it.
Warns against short-circuiting battery terminals and its consequences.
Describes the process of cutting logs or branches into sections.
Outlines fundamental safety rules applicable to all power tools.
Explains kickback and how operators can prevent it.
Warns against short-circuiting battery terminals and its consequences.
Describes the process of cutting logs or branches into sections.
General| Type | Cordless Chainsaw |
|---|---|
| Battery Voltage | 36V |
| Voltage | 36V |
| Chain Gauge | 1.3 mm |
| Oil Tank Capacity | 200 ml |
| Battery Type | Li-ion |
| Power Source | Battery |
| Guide Bar Length | 35 cm (14") |
| Bar Length | 35 cm |
| Chain Pitch | 3/8" |
| Chain Speed | 20 m/s |
To Next Page
