Why is the main power lamp blinking green on my Makita Cordless Saw?
The main power lamp blinking green on your Makita Cordless Saw indicates the switch trigger is being pulled under an unoperable condition. Ensure the main power switch is on and the chain brake is released before pulling the switch trigger.
What to do if there is no oil on the chain of my Makita Chainsaw?
If you notice no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so refill it. Another possible reason is a dirty oil guide groove, which requires cleaning. You may also need to adjust the amount of oil delivery with the adjusting screw if the oil delivery is poor.
What to do if the saw chain does not run on my Makita DUC356 Chainsaw?
If the saw chain of your Makita Chainsaw does not run, it is likely because the chain brake is activated. Release the chain brake to allow the chain to run.
Why the saw chain cannot be installed on my Makita DUC356 Chainsaw?
If the saw chain cannot be installed on your Makita Chainsaw, the combination of saw chain and sprocket is not correct. Use the correct combination of saw chain and sprocket by referring to the section for specifications.
What causes abnormal vibration in my Makita Cordless Saw?
If you experience abnormal vibration with your Makita Cordless Saw, immediately stop the machine. Check for a loose guide bar or saw chain and adjust the tension. If the problem persists, it may indicate a tool malfunction.
Why is Torque Boost mode not available on my Makita Cordless Saw after replacing the battery?
If the Torque Boost mode isn't available after replacing the battery in your Makita Cordless Saw, continue using the tool in normal mode until the installed battery is empty. Then, replace or recharge the battery.
Why is the main power lamp blinking green on my Makita DUC356?
If the main power lamp on your Makita Chainsaw is blinking green, it means that the switch trigger is being pulled under an inoperable condition. Pull the switch trigger after the main power switch is turned on and the chain brake is released.
Why is the Torque Boost mode not available on my Makita Chainsaw?
If the Torque Boost mode is not available on your Makita Chainsaw after replacing the battery cartridge, use the tool in the normal mode until the installed battery cartridge becomes empty, and then replace the battery cartridge with a fully charged one, or recharge the battery cartridge.
What does it mean when the main power lamp is blinking green on my Makita DUC356?
If your Makita Chainsaw's main power lamp is blinking green, it means the switch trigger is being pulled under an inoperable condition. Ensure the main power switch is turned on and the chain brake is released before pulling the switch trigger.
Why does the motor of my Makita Chainsaw stop after a little use?
If your Makita Chainsaw motor stops running after a short period, the battery charge level is likely low. Recharge the battery cartridges, and if recharging doesn't help, consider replacing the battery cartridge.
Specifies the available lengths for the guide bar, crucial for selecting the correct accessory.
Lists compatible chain types like 90PX, 91PX, and 25AP for the chainsaw.
Explains various safety icons and symbols used in the manual for safe operation.
Details the tool's intended applications and its noise emission characteristics.
Covers essential safety guidelines applicable to all power tools.
Provides critical safety precautions specific to cordless chain saw operation.
Details vibration emission levels for different models during operation.
Highlights safety advice specific to chainsaw operation and potential hazards.
Lists essential personal protective equipment (PPE) for safe chainsaw operation.
Discusses vibration risks and how to mitigate them, including protective measures.
Crucial safety guidelines for handling and using battery cartridges.
Provides recommendations to extend the maximum lifespan of the battery.
Identifies and labels the various components of the tool.
Explains how to check and interpret the remaining battery capacity indicators.
Describes how to turn the tool on and off using the main power switch.
Explains the functions of overload, overheat, and overdischarge protection systems.
Details the operation of the switch trigger and lock-off lever for safe starting.
Instructions on how to test and verify the proper functioning of the chain brake.
Step-by-step guide on how to properly tension the saw chain.
Explains the automatic lubrication system and how to refill the oil tank.
Provides guidance on safe methods for operating the chainsaw during cutting tasks.
Defines the conditions and criteria for sharpening the saw chain effectively.
Details the process and angles for sharpening the saw chain using files.
Instructions for cleaning debris from the guide bar groove and sprocket cover.
Outlines a schedule for regular inspection and maintenance of the chainsaw components.
Addresses issues like the chainsaw not starting or the chain not running.
Covers problems related to motor stopping, oil delivery, and RPM issues.
Lists recommended optional accessories and their proper usage.
General| Idle speed | - RPM |
|---|---|
| Motor type | Brushless |
| Chain pitch | 3/8 \ |
| Chain speed | 20 m/s |
| Blade length | 350 mm |
| Product color | Black, Blue |
| Oil tank capacity | 0.2 L |
| Oil level indicator | Yes |
| Power source | Battery |
| Battery voltage | 18 V |
Weight and Dimensions| Length | 270 mm |
|---|---|
| Weight | 5100 g |
To Next Page
