Makita ER2650LH - User Manual

Other manuals for Makita ER2650LH

Technical Information14 pages

Original Instruction Manual38 pages

Questions and Answers

M
Mark MillerSep 3, 2025
What to do if the cutting attachment on my Makita ER2650LH doesn't rotate?
- V
  Veronica WheelerSep 3, 2025
  If the cutting attachment on your Makita Trimmer doesn't rotate, stop the engine immediately. This could be due to the cutting attachment not being tightened securely (tighten the cutting attachment securely), or a twig being caught between the cutting attachment and the protector (remove the foreign matter). If the drive system does not work properly, ask Makita authorized service center to inspect and repair it.
X
Xavier FrankSep 18, 2025
What to do if my Makita ER2650LH engine won't stop?
- G
  gilbertoliviaSep 18, 2025
  If the Makita Trimmer engine does not stop, run the engine at idling and set the choke lever to CLOSE. The issue might be a detached connector (attach securely). For abnormal electric system, request inspection and maintenance.
D
Daniel GarciaSep 16, 2025
Why is my Makita ER2650LH vibrating so much?
- K
  kathy91Sep 16, 2025
  If your Makita Trimmer vibrates abnormally, stop the engine immediately. Possible causes include a broken cutting attachment (replace it), a cutting attachment that is not tightened securely (tighten it securely), or one end of the nylon cutting cord being broken and the nylon cutting head becoming unbalanced (feed the nylon cutting cord by tapping the nylon cutting head on the ground). For a drive system that does not work properly, ask Makita authorized service center to inspect and repair it.
A
Antonio NicholsonSep 14, 2025
What to do if Makita ER2650LH engine stops soon after starting?
- E
  Emily HillSep 14, 2025
  If your Makita Trimmer engine stops soon after starting or the engine speed doesn't increase, it could be due to insufficient warm-up (perform warm-up operation), the choke lever being set to “CLOSE” after warm-up (set to “OPEN”), a clogged fuel filter (clean or replace), or a contaminated or clogged air cleaner (clean it). For abnormal carburetor or drive system, request inspection and maintenance.
B
brandonlewisSep 12, 2025
What to do if my Makita Trimmer engine does not stop?
- D
  Drew MyersSep 12, 2025
  If your Makita Trimmer engine does not stop, run the engine at idling and set the choke lever to CLOSE. Check for any detached connectors and securely attach them. If the issue persists, there may be an abnormality in the electric system, requiring inspection and maintenance.
C
Christopher ScottSep 12, 2025
What to do if my Makita Trimmer engine stops soon after starting?
- S
  Samantha CooleySep 12, 2025
  If your Makita Trimmer engine stops soon after starting or the engine speed does not increase, consider the following: * Ensure you perform a sufficient warm-up operation. * Check that the choke lever is set to “?PE?” and not “CLOSE” after the engine warms up. * Clean or replace a clogged fuel filter. * Also, clean any contamination from the air cleaner. * If the issue persists, there might be a problem with the carburetor or drive system requiring professional inspection and maintenance.
J
Joseph MartinSep 9, 2025
Why is the nylon cutting cord not cut off at the correct length on my Makita ER2650LH?
- B
  Brandon AndersonSep 9, 2025
  If the nylon cutting cord is not being cut off at the correct length on your Makita Trimmer: * The cord extends past the protector. Rewind the cord.
M
Mr. Tyler Hernandez MDSep 7, 2025
What to do if Makita ER2650LH Trimmer engine does not stop?
- M
  Megan PopeSep 7, 2025
  If the engine of your Makita Trimmer does not stop, check if the connector is detached and attach it securely.
J
Joseph HallSep 5, 2025
What to do if my Makita ER2650LH Trimmer vibrates abnormally?
- A
  April RiversSep 5, 2025
  If your Makita Trimmer is vibrating abnormally, stop the engine immediately and check the following: * The cutting attachment might be broken. Replace it with a new one. * The cutting attachment might not be tightened securely. Tighten it securely. * One end of the nylon cutting cord might be broken, causing the nylon cutting head to become unbalanced. Feed the nylon cutting cord by tapping the nylon cutting head on the ground.
S
sanchezmichaelAug 20, 2025
Why won't my Makita Trimmer engine start?
- S
  Spencer MartinAug 21, 2025
  There are several reasons why your Makita Trimmer engine might not be starting: * You may have failed to operate the primer pump. Push it 7 to 10 times. * The pulling speed of the starter rope might be too low. Pull it strongly. * There might be a lack of fuel. Feed fuel to the trimmer. * The fuel filter could be clogged. Clean it. * The fuel tube might be broken. Straighten the fuel tube. * The fuel may be deteriorated. Replace it with new fuel (recommended every month). * The plug cap might be detached. Attach it securely. * The spark plug could be contaminated. Clean it. * The spark plug clearance might be abnormal. Adjust the clearance. * There might be another abnormality with the spark plug. Replace it.