To Next PageTo Next Page
Need help?Do you have a question about the Makita RT0702CX3J and is the answer not in the manual?
The tool is intended for flush trimming and profiling of wood, plastic and similar materials.
The tool should be connected only to a power supply of the same voltage as indicated on the nameplate.
The typical A-weighted noise level determined according to EN62841-2-17.
The vibration total value (tri-axial vector sum) determined according to EN62841-2-17.
For European countries only. The EC declaration of conformity is included as Annex A to this instruction manual.
Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
To adjust the bit protrusion, open the locking lever and move the base up or down as desired by turning the adjusting screw.
To start the tool, press the I side of the switch. To stop the tool, press the O side of the switch.
Indicates tool status: green when plugged, may indicate defects if not lit or blinks red.
Prevents unintentional starting. Blinks red if active. Press 'O' to cancel.
Minimizes start-up shock for a smooth, controlled start.
Maintains constant speed under load for fine finishing.
How to change the tool speed using the dial from 1 to 6 for optimal material processing.
Step-by-step guide for installing or removing trimmer bits using provided wrenches.
Instructions for setting up and using the tool with the base for cutting operations.
Instructions for attaching and using the optional resin base accessory.
How to attach and use the templet guide with patterns for precise cuts.
Attaching and using the straight guide for precise straight cuts and chamfering.
Method for cutting circles using the straight guide and guide plate with specific radius limitations.
Attaching and using the trimmer guide for curved cuts on veneers and similar materials.
Instructions for using the tilt base for chamfering and edge trimming.
Steps for installing and using the offset base for trimming in confined spaces.
How to install and use the plunge base for router operations and depth adjustment.
Detailed procedure for setting the precise cutting depth using the plunge base's adjustment mechanisms.
Attaching and adjusting the straight guide assembly on the plunge base using a guide holder.
Attaching and adjusting the straight guide using guide bars on the plunge base.
How to attach and use the templet guide with patterns when using the plunge base.
Instructions for installing dust nozzles on the base or plunge base for dust extraction.
Procedure for checking the wear and replacing the carbon brushes when necessary.
Lists recommended accessories for the tool, noting potential variations by country.
Table detailing dimensions (D, A, L1, L2) for straight trimmer bits.
Table detailing dimensions (D, A, L1, L2, R) for U-grooving bits.
Table detailing dimensions (D, A, L1, L2, θ) for V-grooving bits.
Table detailing dimensions (D, A, L1, L2, L3) for drill point flush trimming bits.
Table detailing dimensions (D, A, L1, L2, L3, L4) for drill point double flush trimming bits.
Table detailing dimensions (D, A1, A2, L1, L2, L3, R) for corner rounding bits.
Table detailing dimensions (D, A, L1, L2, L3, θ) for chamfering bits.
Table detailing dimensions (D, A, L1, L2, R) for cove beading bits.
Table detailing dimensions and specifications for corner rounding bits, in Spanish.
Table detailing dimensions and specifications for chamfering bits, in Spanish.
Table detailing dimensions and specifications for half round molding bits, in Spanish.
Table detailing dimensions and specifications for flush trimming bits with bearing, in Spanish.
Table detailing dimensions and specifications for corner rounding bits with bearing, in Spanish.
Table detailing dimensions and specifications for chamfering bits with bearing, in Spanish.
Table detailing dimensions and specifications for chamfering bits with bearing, in Danish.
Table detailing dimensions and specifications for beading bits with bearing, in Danish.
Table detailing dimensions and specifications for curved beading bits with bearing, in Danish.
Table detailing dimensions and specifications for antique cornice bits with bearing, in Danish.
Table detailing dimensions and specifications for corner beading bits, in Turkish.
Table detailing dimensions and specifications for Roman ogee bits, in Turkish.
Table detailing dimensions and specifications for groove corner bits, in Turkish.
General
