Manitou MLT625-75 H S1-E3 - Page 113

3-23-277
NOTE: After an accident, replace the seat belt.NOTE: After an accident, replace the seat belt.
In no event should the lift In no event should the lift truck be used if the seat belt truck be used if the seat belt is defective (fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately.is defective (fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately.
E6 - REAR AXLE DIFFERENTIAL OILE6 - REAR AXLE DIFFERENTIAL OIL
DRAINDRAIN
Place the lift truck on level ground Place the lift truck on level ground with the I.C. engine stopped and the d oil still warm.with the I.C. engine stopped and the d oil still warm.
Dispose of the drain Dispose of the drain oil in oil in an ecological manner.an ecological manner.
- Place a container under drain plug 1 (fig. E6) and unscrew - Place a container under drain plug 1 (fig. E6) and unscrew them.them.
-- Remove level and filliRemove level and filling plug 2 (fig. E6) to ensure that the oil is drained properlyng plug 2 (fig. E6) to ensure that the oil is drained properly..
-- Refit and Refit and tighten drain pltighten drain plug 1 (fig. ug 1 (fig. E6) (tightening E6) (tightening torque 34 to 49torque 34 to 49 N.m).N.m).
-- Fill up with oil (see: 3 - MAINTENANCFill up with oil (see: 3 - MAINTENANCE: LUBRICANE: LUBRICANTS AND FUEL) through filler port 2 (fig. E6).TS AND FUEL) through filler port 2 (fig. E6).
- The level is correct - The level is correct when the oil level is flush with the edge of the when the oil level is flush with the edge of the hole.hole.
- Check for any possible leaks at the drain plug.- Check for any possible leaks at the drain plug.
-- Refit and tighten level and fillRefit and tighten level and filling plug 2 (fig. E6) (tightening torque 34 to 4ing plug 2 (fig. E6) (tightening torque 34 to 4
99
N.m)N.m)
25-36lbf/ft25-36lbf/ft
..
E7 - FRONT AND REAR WHEELS REDUCERS OILE7 - FRONT AND REAR WHEELS REDUCERS OIL
DRAINDRAIN
Place the lift truck on level ground with the I.C. engine stopped and the reducers oil stillPlace the lift truck on level ground with the I.C. engine stopped and the reducers oil still
warm.warm.
Dispose of the drain Dispose of the drain oil in oil in an ecological manner.an ecological manner.
- Drain and change the oil of each - Drain and change the oil of each wheel reducer.wheel reducer.
- Place drain pl- Place drain plug 1 (fig. E7) ug 1 (fig. E7) in positionin position A.A.
- Place a container under the drain plug and unscrew - Place a container under the drain plug and unscrew the plug.the plug.
- Let the - Let the oil drain fully.oil drain fully.
- Place the drain port in position B, i.e. in a level port.- Place the drain port in position B, i.e. in a level port.
-- Fill up with oil (see: 3 - MAINTENANCFill up with oil (see: 3 - MAINTENANCE: LUBRICANE: LUBRICANTS AND FUEL) through level port 1 (fig. E7).TS AND FUEL) through level port 1 (fig. E7).
- The level is correct - The level is correct when the oil level is flush with the edge of the when the oil level is flush with the edge of the hole.hole.
- Refit and tight- Refit and tighten the drain plug (tien the drain plug (tightening torque 34 to 49ghtening torque 34 to 49 N.m)N.m)25-36-lbf/ft25-36-lbf/ft..
E7E7
BB
AA
11
E6E6
11
22

https://www.forkliftpdfmanuals.com/