4
OK
CALL
CODE
DELETE
OK
CALL
CODE
DELETE
Please Read card
The card reader
* Speaker volume: Press to enter the page of speaker volume:
Operation:0
---
7
, 0-7 for the speaker volume level. The higher value, the louder.
>_
The page shows "Speaker Volume: 6" means the current speaker volume. Return to previous post automatically when enter the relative number.
* Set time: Press to enter the page of time setting, and could set your locate time.
Please note: The original time of panel is: "00:00" and "2014.06.01", please reset it after get the panel.
1. 3G only
* Mode setting: Press key
5KJD
will enter the page of setting signal mode:
2. 3G
only
.
1. Guard phone
III.
User set: Press to enter the page of user setting:
2.
User
phone
4. Code length
* Guard phone: Press to enter the page of guard phone, Guard room number is 4 digits " 0000 ", then input three phone No, press
after input the first phone No., After input three phone numbers, press
OK
CALL
return to previous post after input the last phone number.
* User phone: Press to enter the page of user phone, it will show
on your panel capacity).
For ex
ample 1. If want to create a new user information:
ID:1
Name:
>Room NO.:
1:
2:
3.
, (ID will start from number 1 automatically. The max ID depends
The capacity of this panel is 512 homes, then ID only could input 1~512. Now press enter the page from ID 1, then input Username/
Room Number and three phone numbers (Could set any 4 digits room number). At the mean time the keyboard is in the lower case mode.
Could press to change the letters mode, press to make a space, press to delete mistakes letters, press to confirm
(Please don’t input same room number twice on one device, if the same room number, it will shows:
Next* Cancel #
).
For example 2. If you want to
modify one room number or username:
The resident of room number 2, which already moved, then come a new one, now need to modify room number 2. First step, to check index no,
ID
Name:
then back the page:
Pls input index:
, input this index, it will show you: , then press , move to next page:
>Room NO.:
, now could input
2:
3.
new
resident information. Also
could SMS
to
modify
the
user information.
* Query: Press to enter the page of searching user information basic on room number: Pls input room NO.: input the room No you want to check.
Then it will display:
OK
, could get ID(Index), username and phone numbers. Press
to return previous
page or
it
will back
main menu
CALL
automatically after 5 seconds.
Unlock code
* Code Length: Press to enter the page of unlocking code length setting
Length: 2----6
. The code length is 2 to 6, the default code length is 6
Input length: 3
>
digits. After input correct will return to last page.
1. Registered
2.
Delete
IV.
Entrance guard: Press to enter the page of entrance guard setting:
3. Empty
4. Read the card
1> Registered: press to enter the page of registered with " Bi ": , then swipe the card (could continuously to record cards, "BiBi"
means record one card ok). It will return to last page automatically after 3 seconds with "BiBiBi" means record card successfully.
Enter card No
2> Delete: press to enter the page of delete:
> , input the card number (12 digits card number), then press . Will return previous
page after 5 seconds (Delete card one by one).
3> Empty: press to enter the page of empty:
Empty
to empty all cards. It should be waited for 3 mins to delete all cards data after enter empty
page, after finished could hear " Bi " and return last page automatically.
4> Read the card: press to enter the page of read the card: . Then swipe the card, you will get the card number (12 digits car d no).
Please Note: Regarding Register and Delete card, also could SMS to operate via Guard phone number.
Delete Card: 06*#12 digits ID card number; Register new card: 07*#12 digits ID card number. If
less 12 digits, please add the digits “0” to the front.
V.
Date
transfer via
software on
PC
:
This function
should be
used
with
software
"GSM
edit
software”
on
computer.
Could
input
al
l
resident data
via software, please check below installation:
*
Unzip
the file
“GSM
edit
software" on computer.
* Put the Unzip file “GSM" to the root directory.
* Double press “ regoxc.bat" to operate, it will show as below pic:
OK
CALL
>ID: ABC
1:1391234
2:23456
3:13546
Same Index Exist
Next* Cancel #
To Next Page
Loading...