Maquet VENTA MULTI CARE 16

Questions and Answers

J
Jennifer MartinAug 14, 2025
What to do if Maquet VENTA MULTI CARE 16 septic fluid suction pump runs but does not extract?
- K
  Kristine GallegosAug 15, 2025
  If the Maquet Medical Equipment septic fluid suction pump runs but does not extract, check the liquid level in the septic fluid jar. Empty the septic fluid jar and clean the overflow protection device as required. Also, replace the bacterial filter if it is clogged. Inspect the tubes for any clogs or incorrect connections. If none of these steps work, the motor may be defective, and you should have the equipment repaired by a service technician authorized by MAQUET.
A
Amanda WatsonAug 18, 2025
Why Maquet VENTA MULTI CARE 16 septic fluid suction pump does not achieve maximum vacuum?
- T
  Todd DicksonAug 18, 2025
  If the Maquet Medical Equipment septic fluid suction pump does not achieve maximum vacuum within 20 seconds, check all septic fluid jar components for visible damage. Also, ensure that tubes and the septic fluid jar cap are properly seated. Replace the bacterial filter if it is clogged. If the issue persists, the motor may be defective, requiring repair by a service technician authorized by MAQUET.
J
James JenkinsAug 21, 2025
What to do if Maquet Medical Equipment septic fluid suction pump does not start?
- R
  Rachael LinAug 21, 2025
  If the Maquet Medical Equipment septic fluid suction pump does not start but the operating status display is illuminated, first switch off the pump. Then, turn the regulating knob to the left and switch the pump back on. Also, check the equipment and mains plugs for proper contact. Verify that the building's circuit breakers are in working condition and check the specifications on the type plate. Replace the mains fuse if it is blown. If the problem persists, the motor may be defective, requiring repair by a service technician authorized by MAQUET.
C
Christina StephensAug 25, 2025
What happens if Maquet Medical Equipment septic fluid suction pump has been exposed to oversuction?
- M
  Melissa Robinson MDAug 25, 2025
  If the Maquet Medical Equipment septic fluid suction pump has been exposed to oversuction, stop using it immediately. The cause may be that there is no mechanical overflow protection device and no hydrophobic bacterial filter installed. Have the equipment repaired by a service technician authorized by MAQUET.
N
natalie21Aug 27, 2025
How to fit septic fluid jar in Maquet VENTA MULTI CARE 16 Medical Equipment?
- R
  robertsantiagoAug 27, 2025
  If the Maquet Medical Equipment septic fluid jar does not fit, it might be inserted in the wrong position. To correct this, insert the septic fluid jar with the scale facing to the front.
W
Walter BellAug 31, 2025
What to do if Maquet VENTA MULTI CARE 16 Medical Equipment septic fluid suction pump working but vacuum gauge indicates no vacuum?
- L
  Lori CarrilloAug 31, 2025
  If the Maquet Medical Equipment septic fluid suction pump is working but the vacuum gauge indicates no vacuum, the vacuum gauge may be defective. Have the equipment repaired by a service technician authorized by MAQUET.
S
Susan HughesSep 3, 2025
What to do if Maquet VENTA MULTI CARE 16 cannot be switched on and off?
- A
  Amy CabreraSep 4, 2025
  If the Maquet Medical Equipment cannot be switched on or off, the electronic circuits may be defective. Have the equipment repaired by a service technician authorized by MAQUET.
K
Kevin CalderonSep 7, 2025
What to do if Maquet Medical Equipment septic fluid suction pump runs but operating status display is not illuminated?
- A
  Amanda ClarkSep 7, 2025
  If the Maquet Medical Equipment septic fluid suction pump runs but the operating status display is not illuminated, the LED at the operating status display may be defective. Have the equipment repaired by a service technician authorized by MAQUET.
B
bryanolsonSep 10, 2025
What causes vacuum cannot be regulated in Maquet VENTA MULTI CARE 16 Medical Equipment?
- D
  Douglas PalmerSep 10, 2025
  If the vacuum cannot be regulated on the Maquet Medical Equipment, the regulating valve may be defective. Have the equipment repaired by a service technician authorized by MAQUET.

Maquet VENTA MULTI CARE 16 Specifications

General

Category	Medical Equipment
Type	Ventilator
Model	VENTA MULTI CARE 16
Manufacturer	Maquet
FiO2 Range	21 - 100 %
Ventilation Modes	CPAP
Patient Type	Adult, Pediatric, Neonatal
Respiratory Rate Range	1 - 80 breaths per minute
PEEP Range	0 - 20 cmH2O
Power Supply	100 - 240 V AC, 50/60 Hz
Display	Color touchscreen
Application	Intensive care, emergency, and transport ventilation