Need help?Do you have a question about the Marantec Synergy 270 and is the answer not in the manual?
Details the numerous state-of-the-art features for convenient and safe operation of the garage door operator.
EOS system provides user-friendly setup and automatic parameter learning for efficient operator function.
Energy-efficient lighting that requires no bulb replacement.
Features automatic soft start and soft stop for smooth operation and increased service life.
Achieved through precision engineering and carefully selected materials for quiet performance.
Allows plug-in of different frequency modules for customized operation.
Patented drive system delivers optimum power for safe door movement every time.
Infrared beam system detects obstructions, reversing the door to protect people and property.
Offers easy navigation through levels and menus for operator control.
Indicates the current status of the door operator for easy monitoring.
Provides a quicker and easier setup process for parameters.
Facilitates quicker troubleshooting by displaying error codes.
Optimizes operator service life and trouble-free performance through scheduling.
Confirms compliance with UL 325 safety standards for garage door operators.
Crucial safety warnings regarding garage doors, their weight, and potential hazards.
Cautionary notes regarding property damage or injury from improper installation.
Instructions for reporting missing hardware to Marantec America customer service.
Critical warnings to reduce the risk of severe injury or death during installation.
Warnings about potential injury from tools and the need for protective equipment.
Steps to mark the vertical center line on the door and header for alignment.
Instructions to measure the door's highest travel point for clearance calculations.
Guidance on marking the horizontal line for header bracket mounting.
Instructions for attaching the door bracket to wood sectional doors.
Warning about the importance of securely fastening the header bracket for safety system function.
Warning to use only provided screws when fastening the rail to the operator head to prevent falling.
Warning that improper securing can cause injury if the operator falls.
Important note on locking the trolley and moving the door manually.
Warnings to prevent serious injury or death from a falling garage door during emergency release.
Caution to ensure photo eye sensors are mounted correctly for maximum protection.
Instructions for mounting the photo eye sensor brackets to the wall.
Steps for mounting the photo eye sensors onto the prepared mounting bracket.
Guidance on routing sensor wires safely and securely along walls and rails.
Advice on protecting photo eye sensors during garage maintenance activities.
Specific instructions for installing photo eye sensors in dual garage door setups.
Instructions for installing and wiring multiple wall control panels in parallel.
Warning about the danger of electric shock and the need for disconnection during wiring.
Warning to prevent electrocution or fire by following codes and using proper grounding.
Contact information for obtaining replacement power cords from Marantec America.
Warning to ensure the door is closed and engaged to the drive system before programming.
Important notes on initial open travel activation and travel limit checks.
Important note requiring two complete cycles after initial setup.
Warnings about injury due to uncontrolled door operation and property damage.
Instructions for mounting the transmitter using a visor clip or mounting plate.
Procedures for transferring codes between transmitters for multiple openers.
Warnings to prevent injury or death from a moving garage door.
Steps to program personal identification numbers (PINs) and transfer codes for the WKE system.
How the operator activates using the Keyless Entry system with PIN and ENTER button.
Instructions on how to operate the door using a remote control transmitter.
How to operate the door using the wall control panel and its buttons.
Information on how the operator light functions and its settings.
How to align photo eye sensors for proper beam visibility and operation.
Steps to test the photo eye sensors' ability to detect obstructions and prevent door movement.
How to check the belt or chain tension for correct setting.
Step-by-step instructions for increasing or decreasing belt/chain tension.
Lists parts for the belt-driven rail assembly.
Lists parts for the chain-driven rail assembly.
Warning about electric shock hazard when working with wiring and the power supply.
Instructions for assembling the LED cluster components.
Steps for installing the new LED cluster into the operator housing.
Caution regarding short and rapid cycles causing motor/transformer overheating.
Recommended monthly maintenance checks for safety reversal, door operation, and photo eye system.
Annual maintenance recommendations, including lubrication of door components.
Guidance on when and how to readjust travel limits, force settings, and belt tension.
General| Motor Type | DC |
|---|---|
| Type | Residential Garage Door Opener |
| Horsepower equivalent | 1/2 HP |
| Security | Rolling code technology |
| Remote Controls Included | 2 |
| Drive Type | Chain |
To Next Page