Marantz AV9000 - Service Manual

Other manuals for Marantz AV9000

User Guide41 pages

Specifications1 page

Questions and Answers

S
Sherry PowersSep 8, 2025
Why can't I play DTS sources on my Marantz Tuner?
- M
  Marc NobleSep 9, 2025
  If DTS sources cannot be played, it may be because the Surround mode is set to DOLBY, or the player does not respond to DTS digital out. Select another mode. Use a player which responds to DTS-digital out.
W
William CurryAug 23, 2025
What to do if no sound and picture from Marantz AV9000 Tuner even when power is on?
- R
  Robert JohnsonAug 23, 2025
  If there's no sound and picture even when the power is on, try these steps: First, ensure that mute is off by using the remote control. Next, check the input cable connections against the connection diagram to make sure they are correctly connected. Then, adjust the master volume to an audible level. Finally, verify that the function selector is set to the correct position.
K
Kelly DaughertyAug 25, 2025
How to fix FM or AM reception failure on Marantz AV9000 Tuner?
- M
  Megan CampbellAug 26, 2025
  If FM or AM reception fails, ensure that the indoor FM and AM antennas are correctly connected to the FM and AM antenna outlets.
C
claire11Aug 27, 2025
Why is the display on my Marantz AV9000 remote commander blank?
- K
  kimberly48Aug 27, 2025
  If nothing appears on the remote commander display, the batteries are likely dead. Replace all the batteries with new ones.
J
Jennifer RayAug 27, 2025
What to do if I cannot change the surround mode on my Marantz AV9000 Tuner?
- S
  Stephanie JenkinsAug 27, 2025
  If you cannot change the surround mode, check if headphones are connected to the jack. Disconnect the headphones, as the surround mode is fixed to STEREO when headphones are connected.
M
millerjenniferSep 22, 2025
Why is a specific channel not producing output on my Marantz AV9000?
- R
  roy85Sep 22, 2025
  If a specific channel does not produce output, it may be because nothing is recorded on the source. Check the encoded channel on the source side.
T
Thomas DavisSep 16, 2025
Why can't I play a 96kHz PCM signal on my Marantz AV9000 Tuner?
- M
  Mark BeardSep 16, 2025
  If a 96kHz PCM signal cannot be played, it may be because the player does not respond to 96kHz PCM digital out, or the Surround mode is set to other than STEREO and AUTO. Use a player that responds to 96 kHz PCM digital out. Set Surround mode to STEREO or AUTO.
S
Samantha MartinSep 18, 2025
What to do if my Marantz Tuner skips and produces noise when playing a DTS source?
- C
  connie92Sep 18, 2025
  If the player skips during the play of a DTS source and produces noise, it might be due to a data error during the player skip. Set Surround mode to DTS-cinema or DTS-music.
P
paul78Sep 7, 2025
What to do if I cannot get programmed station when pressing PRESET button on Marantz Tuner?
- D
  david84Sep 7, 2025
  If you cannot get a programmed station when pressing the PRESET button, the preset data may have been erased. Disconnecting the power plug for long periods can erase this data. If this happens, input the preset data again.
S
Stacey MaysSep 4, 2025
Why am I getting sound and pictures from equipment other than what's selected on my Marantz Tuner?
- J
  jenglishSep 4, 2025
  If you're getting sound and pictures from equipment other than what you selected, the input cable is likely connected incorrectly. Connect the cable correctly by referring to the connection diagram.