Why does my Marantz NR1403 Stereo Receiver automatically switch to standby mode?
Your Marantz Stereo Receiver might be automatically switching to standby mode because the sleep timer is set. Turn the power back on or adjust the sleep timer settings. Alternatively, the “Auto Standby” feature may be enabled, which is triggered when no commands are received for a certain time. You can disable this by setting “Auto Standby” to “Off” in the menu.
Why my Marantz NR1403 power does not turn on?
If your Marantz Stereo Receiver doesn't turn on, first check if the power plug is properly inserted into the power outlet. If it is, the protection circuit might be active. Disconnect the power plug from the outlet, wait 5 to 10 seconds, and then plug it back in.
How to fix no audio output with HDMI connection on Marantz Stereo Receiver?
If you're experiencing no audio output with an HDMI connection on your Marantz Stereo Receiver, first check the connection of the HDMI connectors. If you want to output audio from the speakers, set “HDMI Audio Out” on the menu to “AVR”. If you want to output audio from a TV, set “HDMI Audio Out” on the menu to “TV.”
Why no sound is produced from subwoofer on Marantz Stereo Receiver?
If you're not getting any sound from the subwoofer connected to your Marantz Stereo Receiver, check the subwoofer connections and ensure the subwoofer is powered on. On the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes.” Also, if “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected sound mode.
Why the volume does not increase on Marantz NR1403?
If the volume on your Marantz Stereo Receiver isn't increasing as expected, the maximum volume might be set too low. Adjust the maximum volume under “Limit” in the menu. Also, make sure that the power for any external devices connected to the unit's output connectors is turned on.
Why Audyssey MultEQ, Audyssey Dynamic EQ and Audyssey Dynamic Volume cannot be selected on Marantz NR1403?
If Audyssey MultEQ®, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected on your Marantz Stereo Receiver, switch the sound mode to other than “DIRECT” or “PURE DIRECT.” Also, these features cannot be selected when headphones are used.
How to turn on display on Marantz NR1403?
If the display on your Marantz Stereo Receiver is off, set “Display” on the menu to something other than “Off.”
Why M-DAX cannot be selected on Marantz NR1403 Stereo Receiver?
If M-DAX cannot be selected on your Marantz Stereo Receiver, ensure that an analog signal or PCM signal (Sample rate=44.1/48 kHz) is input. M-DAX cannot be used for playback of multichannel signals like Dolby Digital or DTS surround. Also, switch the sound mode to something other than “DIRECT” or “PURE DIRECT.”
What to do if no video is output with HDMI connection on Marantz NR1403 Stereo Receiver?
If you're not getting any video output via HDMI on your Marantz Stereo Receiver, start by checking the HDMI connector's connection. Make sure the input source is correctly set to match the HDMI connector you're using. Also, verify that your TV is compatible with copyright protection (HDCP), as incompatible devices may prevent proper video output.
How to troubleshoot no picture on Marantz Stereo Receiver?
If no picture appears on your Marantz Stereo Receiver, check the connection between the video output terminal of the unit and the input terminal of your TV. Also, make sure the input settings on the TV match the input terminal connected to the unit.
General| Receiver type | - |
|---|---|
| Audio output channels | 9.1 channels |
| Signal-to-Noise Ratio (SNR) | 98 dB |
| Power output per channel (1KHz@6 Ohm) | 60 W |
| Power output per channel (20-20KHz@8 Ohm) | 50 W |
| HDMI in | 6 |
| Composite video in | 3 |
| Digital audio optical in | 1 |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Ethernet LAN | No |
| Supported radio bands | AM, FM |
| Product color | Black |
| Audio decoders | Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD |
| Apple docking compatibility | Not supported |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 180 W |
Weight and Dimensions| Depth | 367 mm |
|---|---|
| Width | 440 mm |
| Height | 105 mm |
| Weight | 8300 g |
To Next Page
